1. Registration trouble? Please use the "Contact Us" link at the bottom right corner of the page and your issue will be resolved.
    Dismiss Notice

Recent Content by wellsnmj

  1. wellsnmj
    Post

    Fender flairs

    look sharp where did they come from?
    Post by: wellsnmj, Oct 24, 2009 in forum: Builds and Fabricators Forum
  2. wellsnmj
    Post

    61 Undergoing the knife...or sockets/grinder.etc..

    they were "free" they are military truck seats "surplus" LOL
    Post by: wellsnmj, Oct 18, 2009 in forum: Builds and Fabricators Forum
  3. wellsnmj
    Post

    61 Undergoing the knife...or sockets/grinder.etc..

    haven't had time to do much but we have decided on a color and I got some new seats for it [IMG] [IMG] [IMG]
    Post by: wellsnmj, Oct 18, 2009 in forum: Builds and Fabricators Forum
  4. wellsnmj
    Post

    chevy 2.8 L swap into early cj 5

    Thanks, going to drop him a PM see how he likes it ( if it runs yet...) I just feel the 4.3 would be way overpowered for what I want to do with...
    Post by: wellsnmj, Oct 13, 2009 in forum: Builds and Fabricators Forum
  5. wellsnmj
    Post

    chevy 2.8 L swap into early cj 5

    If I was to do the swap I would sticker with an older carb'd one. As far as underpowered not going to be any less underpowered then the F 134...
    Post by: wellsnmj, Oct 12, 2009 in forum: Builds and Fabricators Forum
  6. wellsnmj
    Thread

    chevy 2.8 L swap into early cj 5

    Just wondering if anyone had done this? I know the latest is the 4.3 but I was thinking the 2.8 might make a decent little engine for it
    Thread by: wellsnmj, Oct 12, 2009, 21 replies, in forum: Builds and Fabricators Forum
  7. wellsnmj
    Post

    Exhaust re-route, suggestions

    Is this because they don't count as spark arresters?
    Post by: wellsnmj, Sep 29, 2009 in forum: Builds and Fabricators Forum
  8. wellsnmj
    Post

    61 Undergoing the knife...or sockets/grinder.etc..

    1 nut and a rubber hammer on the back slid right off just had to walk it off by tapping it evenly so didn't bind the splines in it
    Post by: wellsnmj, Sep 28, 2009 in forum: Builds and Fabricators Forum
  9. wellsnmj
    Post

    61 Undergoing the knife...or sockets/grinder.etc..

    Trying not to kill anyone's computer lol took almost 200 pics this weekend ! Did put up the photobucket link where I'm storing them all how...
    Post by: wellsnmj, Sep 27, 2009 in forum: Builds and Fabricators Forum
  10. wellsnmj
    Thread

    61 Undergoing the knife...or sockets/grinder.etc..

    Well after much hemming and hawing after I bought my 61 cj 5 I've decided to go ahead and keep it. I had it on CL for a while but everyone wanted...
    Thread by: wellsnmj, Sep 27, 2009, 10 replies, in forum: Builds and Fabricators Forum
  11. wellsnmj
    Post

    Slow Build 73 CJ5

    I'm not sure I would stack the bushings like that body mount kits are fairly cheap.. here's an example....
    Post by: wellsnmj, Sep 26, 2009 in forum: Builds and Fabricators Forum
  12. wellsnmj
    Post

    9" wiper blades

    http://www2.partstrain.com/store/details/Jeep/CJ5/Anco/Wiper_Blade/1960/Base/4_Cyl_2-dot-2L/AN2009.html?location=Front found some here
    Post by: wellsnmj, Sep 25, 2009 in forum: Early CJ5 and CJ6 Tech
  13. wellsnmj
    Post

    61 fuel pump

    Why the mechanical? I ask because in my '61 the PO replaced it with an electric and works fine..
    Post by: wellsnmj, Sep 24, 2009 in forum: Early CJ5 and CJ6 Tech
New Posts