1. Registration trouble? Please use the "Contact Us" link at the bottom right corner of the page and your issue will be resolved.
    Dismiss Notice

Recent Activity

Activity stream for all registered members at ECJ5.

  1. tripilio replied to the thread Transfer Case Drive Gear.

    Ok, I will use my yoke tool on the TC, then. That sounds better. Thanks a lot!(y)

    Jan 27, 2020 at 2:30 PM
  2. ITLKSEZ liked tomasinator's post in the thread Limited Slip Recommendations?.

    I installed a Spartan locker in my '76 AMC20's rear diff about five years ago (the jeep in my avatar). [IMG] I haven't noticed any...

    Jan 27, 2020 at 2:30 PM
  3. John Gedde replied to the thread A Full Restoration Of My 1969 Cj5 With The Dauntless.

    It's the closest I could come to the original color. It's Honda Hampstead Green and it's pretty darn close to the color Kaiser/Buick...

    Jan 27, 2020 at 2:30 PM
  4. tripilio liked FinoCJ's post in the thread Transfer Case Drive Gear.

    kind of realized that after fireball posted his comment....I did the transmission into 2gears so it locked in place. You could put a...

    Jan 27, 2020 at 2:29 PM
  5. tripilio liked Fireball's post in the thread Transfer Case Drive Gear.

    You could try a large pipe wrench on the rear output flange with the transfer case in High. Or even bolt a large bar or 2x4 to it using...

    Jan 27, 2020 at 2:29 PM
  6. John Gedde replied to the thread A Full Restoration Of My 1969 Cj5 With The Dauntless.

    Yes and no. Some fasteners and objects I replated, other fasteners are new. For example, the fuel pump heat shield I plated in just...

    Jan 27, 2020 at 2:28 PM
  7. John Gedde replied to the thread Melling Sbc8 Cam.

    Interesting article! I got excited when I saw the table for the OEM cam specs. Then I saw the duration and overlap numbers were from...

    Jan 27, 2020 at 2:22 PM
  8. timgr replied to the thread T90 Transmission Question - What's My First Gear Ratio?.

    It's now a T-90A with the long input gear from a Utility Wagon. The cluster gear has to match the input gear; no mixing parts possible....

    Jan 27, 2020 at 2:12 PM
  9. John Gedde replied to the thread Rope Or Neoprene?.

    You didn't say for what engine, but if it's the 225, Neoprene for sure. Not only is Neo just better, but the rope seals from Fel-Pro...

    Jan 27, 2020 at 2:09 PM
  10. ojgrsoi liked Iandavidh's post in the thread $25,000 Surrey?.

    '63 Willys Surrey Gala Jeep - DJ-3A - Rare - 1963 - DJ3A $25 grand seems a bit steep

    Jan 27, 2020 at 2:06 PM
  11. John Gedde replied to the thread Iso Heat Riser For Dauntless V6. Any Ideas?.

    They're seemingly not obtainable. I made my own since I couldn't find one either... I didn't make drawings when I machined it, I just...

    Jan 27, 2020 at 2:06 PM
  12. ojgrsoi replied to the thread M170.

    M170 It is pretty cool.

    Jan 27, 2020 at 2:03 PM
  13. FlyHelo posted a new thread.

    Iso Heat Riser For Dauntless V6. Any Ideas?

    Hello, new Commando owner. I cannot find a heat riser for the right manifold for my Dauntless V6. Does anyone know where to find a...

    Forum: Jeepster Commando and Commando Tech

    Jan 27, 2020 at 1:51 PM
  14. red61cj5 replied to the thread Rope Or Neoprene?.

    Was trying the neoprene (best gasket 3b71) in the cap and block without the crank in place, just to check fit. Gasket halves stand a...

    Jan 27, 2020 at 1:44 PM
Loading...
New Posts