1. Registration trouble? Please use the "Contact Us" link at the bottom right corner of the page and your issue will be resolved.
    Dismiss Notice

Recent Content by cam saure

  1. cam saure
    Post

    Tub repair panels

    All of the replacement panels that I have seen were sold without the channels. I have seen some nice fabbed floors and mounts using rectangular...
    Post by: cam saure, Jul 13, 2007 in forum: Intermediate CJ-5/6/7/8
  2. cam saure
    Post

    D20 jumps out of 4WD

    The plastic caps only plug the holes. The holes are for inserting the balls and springs, they are underneath the shift shafts. The springs and...
    Post by: cam saure, May 29, 2007 in forum: Intermediate CJ-5/6/7/8
  3. cam saure
    Post

    76 cj wiring diagram

    Yes, I checked the tech section, nothing there pertaining to mine, unless I did something wrong. All I found was for much earlier models and the...
    Post by: cam saure, May 26, 2007 in forum: Intermediate CJ-5/6/7/8
  4. cam saure
    Thread

    76 cj wiring diagram

    Hi, Been a while since I have posted, New job has taken all my time. Has anyone got a copy of a wiring diagram for a 76 CJ5 that they could post...
    Thread by: cam saure, May 26, 2007, 2 replies, in forum: Intermediate CJ-5/6/7/8
  5. cam saure
    Post

    Transmission crossmember

    You may want to be sure that your crossmember isn't switched end for end. IIRC there are some indentations that go to the rear on the pass side. I...
    Post by: cam saure, Aug 1, 2006 in forum: Intermediate CJ-5/6/7/8
  6. cam saure
    Post

    1973 VIN- Please help narrow down DOM...

    I have VIN sequence number 74488. My dash sticker was missing but from the build dates on other components I presume it to be built in June of 73....
    Post by: cam saure, Aug 1, 2006 in forum: Intermediate CJ-5/6/7/8
  7. cam saure
    Post

    Tar Removal inside.. ??????????

    The stuff you use before painting woks fairly well, Prep all or wax and grease remover. You should be able to get Prep all at Napa or wax and...
    Post by: cam saure, Jul 18, 2006 in forum: Early Jeep Restoration and Research
  8. cam saure
    Post

    T-14 to T-15 or T-18

    I looked in the parts book and it appears that in the intermediate years the T14 and T15 use the same bell housing(part # 321 5152). Also in the...
    Post by: cam saure, Jul 17, 2006 in forum: Intermediate CJ-5/6/7/8
  9. cam saure
    Post

    Will this ever end ?

    Jeeps are a lot like being married to some women; You have to work on them all week just to "enjoy" them a little on weekends. But on a serious...
    Post by: cam saure, Jul 17, 2006 in forum: Intermediate CJ-5/6/7/8
  10. cam saure
    Post

    Engine/Water

    There is a number of ways you can go and also some simple tricks. Dilectic silicon grease is a good way to go. But remember the earlier post in...
    Post by: cam saure, Jul 13, 2006 in forum: Intermediate CJ-5/6/7/8
  11. cam saure
    Post

    My cracked frame

    If you decide to put a patch plate/gusset on the side of the frame, don't make it a square plate, rather make it more "bullet shaped at each end....
    Post by: cam saure, Jun 25, 2006 in forum: Intermediate CJ-5/6/7/8
  12. cam saure
    Post

    fender-tub welting?

    I wonder if there is a source for silicon rubber gasket material that could be cut into strips and holes punched in it. I would think that would...
    Post by: cam saure, Jun 23, 2006 in forum: Early Jeep Restoration and Research
  13. cam saure
    Post

    74 Ignition

    My 73 has stock Delco point dist. (no window, like the old Chevy 6 cyl cars) Points (Delco D108P) fit Jeep, Chevy and 70's Harley Davidson big twins.
    Post by: cam saure, May 17, 2006 in forum: Intermediate CJ-5/6/7/8
  14. cam saure
    Post

    1975 Cj -5 turn signals

    They would of had the rectangular red marker lights on the sides. If you had a side mounted spare it would of had a round light in the center of...
    Post by: cam saure, Apr 23, 2006 in forum: Intermediate CJ-5/6/7/8
New Posts