1. Registration trouble? Please use the "Contact Us" link at the bottom right corner of the page and your issue will be resolved.
    Dismiss Notice

Recent Content by jetdoc11

  1. jetdoc11
    Post

    nuts!

    if the stud has a concave end on it you can use an air hammer and suitable bit to remove and install them.
    Post by: jetdoc11, Feb 7, 2007 in forum: Early CJ5 and CJ6 Tech
  2. jetdoc11
    Thread

    the beaten path of wiper linkages..

    Since we all know that too many parts for our Jeeps are unobtainable. I've got a new windshield frame from a 1971, but with no wiper linkage...go...
    Thread by: jetdoc11, Jan 29, 2007, 1 replies, in forum: Early CJ5 and CJ6 Tech
  3. jetdoc11
    Post

    Patch Panel Progress

    great job.
    Post by: jetdoc11, Sep 29, 2006 in forum: Early CJ5 and CJ6 Tech
  4. jetdoc11
    Thread

    leaf measurements

    i know that this topic has been beaten to death in most aspects. i'm trying to sell a full set of 10 leaf pack front and rear springs that were...
    Thread by: jetdoc11, Sep 7, 2006, 1 replies, in forum: Early CJ5 and CJ6 Tech
  5. jetdoc11
    Post

    Quandry, Need Advice

    #2.
    Post by: jetdoc11, Jun 11, 2006 in forum: Early CJ5 and CJ6 Tech
  6. jetdoc11
    Post

    Body Hold Down

    glass or steel? body lift or not?
    Post by: jetdoc11, May 22, 2006 in forum: Early CJ5 and CJ6 Tech
  7. jetdoc11
    Post

    New to CJs/site. Questions.

    i did the d27 disk and d44 11" conversions. i figured with the chevy 350 conversion i might need it and that i was going to use power steering...
    Post by: jetdoc11, May 21, 2006 in forum: Early CJ5 and CJ6 Tech
  8. jetdoc11
    Post

    Fixed: V6 Cutting out at cruising speeds?

    Re: V6 Cutting out at cruising speeds? ****Oops. I missed the part of the "new poly tank"...my bad.****
    Post by: jetdoc11, May 18, 2006 in forum: Early CJ5 and CJ6 Tech
  9. jetdoc11
    Post

    Frame ques on Fiberglass tub

    on my fiberglass tub, the front 4 are 3" and the rear 2 are 2". i had to lift the body to fit the th350 in. if you're looking for a cheap, but...
    Post by: jetdoc11, Apr 29, 2006 in forum: Early CJ5 and CJ6 Tech
  10. jetdoc11
    Post

    Tie-rod flip?? I've walked into a wall here...

    thanks for the info.
    Post by: jetdoc11, Apr 7, 2006 in forum: Early CJ5 and CJ6 Tech
  11. jetdoc11
    Thread

    Tie-rod flip?? I've walked into a wall here...

    I'm in the middle of installing a chevy 350 in my CJ5 and have a bit of an issue with the tie-rod to spring clearance. I've considered shims, but...
    Thread by: jetdoc11, Apr 7, 2006, 4 replies, in forum: Early CJ5 and CJ6 Tech
  12. jetdoc11
    Post

    Replacing stock ECJ5 bumpers, to rivet or bolt?

    if you wanted to rivet it in place you would need an air compressor, an air hammer, a bucking bar and a rivet set. depending on the...
    Post by: jetdoc11, Sep 6, 2005 in forum: Early Jeep Restoration and Research
New Posts