1. Registration trouble? Please use the "Contact Us" link at the bottom right corner of the page and your issue will be resolved.
    Dismiss Notice

Search Results

Search Again
Page 1 of 9
  1. napaguy
    Post

    Fixing a Title issue

    As long as its titled and you arent having issues with license etc let it go..once you start getting the state involved your problems will grow..
    Post by: napaguy, Oct 30, 2012 in forum: Early CJ5 and CJ6 Tech
  2. napaguy
    Post

    New, Used, or Rebuilt Overdrive?

    I have bought a few used overdrives and all of them needed totally rebuilt anyways so my vote is to be a refurbished unit from Herm
    Post by: napaguy, Oct 29, 2012 in forum: Early CJ5 and CJ6 Tech
  3. napaguy
    Post

    sealant for oil pan gasket

    Whatever you decide use sparingly as it can do more harm than good..I always use a very thin coating on both sides mainly to hold the gasket in place
    Post by: napaguy, Oct 28, 2012 in forum: Early CJ5 and CJ6 Tech
  4. napaguy
    Post

    Rookie's 67 Cj5 (re)build - Here We Go....again

    I prefer wire feed with .023 wire and 75/25 gas for sheetmetal...flux will also work but I like welding with gas alot better
    Post by: napaguy, Oct 28, 2012 in forum: Builds and Fabricators Forum
  5. napaguy
    Post

    Rookie's 67 Cj5 (re)build - Here We Go....again

    stick welders should not be used for sheet metal...makes sense why your having problems :)
    Post by: napaguy, Oct 26, 2012 in forum: Builds and Fabricators Forum
  6. napaguy
    Post

    Rookie's 67 Cj5 (re)build - Here We Go....again

    Have you tried using a copper backer when you weld the holes shut? Start in the middle and get a small puddle going then work your way to the...
    Post by: napaguy, Oct 26, 2012 in forum: Builds and Fabricators Forum
  7. napaguy
    Post

    Alternator/Fan blade clearance (issue?)

    Boy thats pretty close..I have to believe that fan is going to flex some when moving as well...can the alternator be moved back some?
    Post by: napaguy, Oct 26, 2012 in forum: Builds and Fabricators Forum
  8. napaguy
    Post

    Should it really be this slow?

    who was "hollerin'"? if stating the fact that somebody dug up a six year old thread and added a comment is "hollerin'" than I guess im guilty..its...
    Post by: napaguy, Oct 23, 2012 in forum: Early CJ5 and CJ6 Tech
  9. napaguy
    Post

    CJ5 rollbar padding

    hmmm dont know about that...I would guess environment, use etc would play into that. Mine stayed in the garage and had no issues but I guess If I...
    Post by: napaguy, Oct 23, 2012 in forum: Early CJ5 and CJ6 Tech
  10. napaguy
    Post

    CJ5 rollbar padding

    I used the pipe insulation and then bought black duct tape and it came out decent
    Post by: napaguy, Oct 23, 2012 in forum: Early CJ5 and CJ6 Tech
  11. napaguy
    Post

    Should it really be this slow?

    holy thread revival batman
    Post by: napaguy, Oct 22, 2012 in forum: Early CJ5 and CJ6 Tech
  12. napaguy
    Post

    Power steering parts?

    You arent going to get a ton of responses because you have asked the third most common question after flat towing and knuckle lube...use the...
    Post by: napaguy, Oct 19, 2012 in forum: Early CJ5 and CJ6 Tech
  13. napaguy
    Post

    axles shims or lower rear spring hanger

    Well Im dumb as a board but here goes...the extra length of the tubing being added equals more leverage on that area which is already iffy...think...
    Post by: napaguy, Oct 15, 2012 in forum: Builds and Fabricators Forum
  14. napaguy
    Post

    Overdrive breakage

    nay sayers? Where?
    Post by: napaguy, Oct 11, 2012 in forum: Flat Fender Tech
  15. napaguy
    Post

    Oddball crossmember

    I am far from an expert but that is different than any oem jeep crossmember I have ever seen...looks like a junkyard piece?
    Post by: napaguy, Oct 10, 2012 in forum: Early CJ5 and CJ6 Tech
  16. napaguy
    Post

    1965 CJ5 (no name yet build)

    HMmm thats news to me but Im far from an expert...sounds pretty RARE
    Post by: napaguy, Oct 9, 2012 in forum: Builds and Fabricators Forum
  17. napaguy
    Post

    1965 CJ5 (no name yet build)

    72 iirc
    Post by: napaguy, Oct 9, 2012 in forum: Builds and Fabricators Forum
  18. napaguy
    Post

    Dealing with body shop guys: need some advice

    In the future the easiest way to deal with a bodyshop is not to use one...I too worked in a body shop
    Post by: napaguy, Oct 7, 2012 in forum: Early CJ5 and CJ6 Tech
  19. napaguy
    Post

    A NEW question about flat towing!

    Gentlemen lets review the forum rules once again...no discussion of religion, politics, pitbulls or flat towing :)
    Post by: napaguy, Oct 7, 2012 in forum: Early CJ5 and CJ6 Tech
  20. napaguy
    Post

    Dual brake master cylinder install issues

    Gotta love the response from Herm...I live near him and can tell you he is a good man and usually very friendly but its apparent you did something...
    Post by: napaguy, Oct 6, 2012 in forum: Early CJ5 and CJ6 Tech
Showing results 1 to 20 of 167 Next >
Search Again
Page 1 of 9
New Posts