1. Registration trouble? Please use the "Contact Us" link at the bottom right corner of the page and your issue will be resolved.
    Dismiss Notice

Recent Content by SwampRatt

  1. SwampRatt
    Post

    Exhaust Popping

    I've been thinking about this too. My 304 with headers and a Edelbrock(Rodchester) 4bbl pops, but only out the passenger side. I haven't pulled...
    Post by: SwampRatt, Aug 4, 2009 in forum: Intermediate CJ-5/6/7/8
  2. SwampRatt
    Post

    Terminal connectors

    Ah, thanks. Looks like what I've called a spade connector or some such.
    Post by: SwampRatt, Nov 4, 2008 in forum: Intermediate CJ-5/6/7/8
  3. SwampRatt
    Post

    Terminal connectors

    I need the wire side. The switch has the terminals, I need to connect to them. So I need the connectors to solder to the end of the wires to...
    Post by: SwampRatt, Nov 4, 2008 in forum: Intermediate CJ-5/6/7/8
  4. SwampRatt
    Thread

    Terminal connectors

    Can someone point me in the direction of where to get terminal connectors for my back up lights? My switch appears to work but isn't wired up. I...
    Thread by: SwampRatt, Nov 3, 2008, 8 replies, in forum: Intermediate CJ-5/6/7/8
  5. SwampRatt
    Post

    Bellcrank question

    The current rod which I believe is stock for a '73 is straight. The rod I made from all thread was thicker and rubbed on the sheet metal where...
    Post by: SwampRatt, Jul 17, 2008 in forum: Intermediate CJ-5/6/7/8
  6. SwampRatt
    Post

    Bellcrank question

    I just ordered a "drop-in" replacement rod and heim joints for 75 bucks. Sadly if I had a shop I'd make em but ......
    Post by: SwampRatt, Jul 17, 2008 in forum: Intermediate CJ-5/6/7/8
  7. SwampRatt
    Post

    Bellcrank question

    Ah yes. Looks like I need to flip the bell crank so the zerk of inboard and change the alignment if the crank.
    Post by: SwampRatt, Jul 17, 2008 in forum: Intermediate CJ-5/6/7/8
  8. SwampRatt
    Post

    Bellcrank question

    Looks like mine in the pic is close to straight down, parallel to the bell housing. The "long" arm is on the side opposite the grease zerk....
    Post by: SwampRatt, Jul 17, 2008 in forum: Intermediate CJ-5/6/7/8
  9. SwampRatt
    Thread

    Bellcrank question

    I had replaced the complete linkage a last year. Yesterday the "ball joint" snapped at the clutch petal. Anyway my question: is the Bellcrank on...
    Thread by: SwampRatt, Jul 17, 2008, 12 replies, in forum: Intermediate CJ-5/6/7/8
  10. SwampRatt
    Post

    No horn or turn signals

    White Jeepers can sleep in peace now. I found mine as well. The PO had run the turn signal wires too close to the clutch petal linkage and it...
    Post by: SwampRatt, Jul 13, 2008 in forum: Intermediate CJ-5/6/7/8
  11. SwampRatt
    Post

    Another What is this?

    Looks like I can get me another battery! :) How would that be wired?
    Post by: SwampRatt, Jul 13, 2008 in forum: Intermediate CJ-5/6/7/8
  12. SwampRatt
    Post

    No horn or turn signals

    I've got a similar problem. The turn signals work for a short trip then the fuse blows. Background: Originally the 30 amp main ignition fuse...
    Post by: SwampRatt, Jul 12, 2008 in forum: Intermediate CJ-5/6/7/8
  13. SwampRatt
    Thread

    Another What is this?

    The gold heat sunk thingie next to the starter solenoid. Can anybody tell me what this is? It either a voltage regulator or dual ballast? I...
    Thread by: SwampRatt, Jul 12, 2008, 5 replies, in forum: Intermediate CJ-5/6/7/8
New Posts