1. Registration trouble? Please use the "Contact Us" link at the bottom right corner of the page and your issue will be resolved.
    Dismiss Notice

Search Results

Search Again
Page 1 of 5
  1. 74CJ
    Post

    Cant get the skip out

    I got it. To answer your question before I make my confession... The distributor is new and I did bypass the resister with the heavier guage wire...
    Post by: 74CJ, Jul 14, 2013 in forum: Intermediate CJ-5/6/7/8
  2. 74CJ
    Post

    Cant get the skip out

    I've the original wire from the donor vehicle of the distributor. It appears to be 12 awg, yes.
    Post by: 74CJ, Jul 14, 2013 in forum: Intermediate CJ-5/6/7/8
  3. 74CJ
    Thread

    Cant get the skip out

    I'm tryin to put an aftermarket hei dist. In my 74 258. It has a skip I can't get out. The distributor is new. Since then I've replaced the plugs,...
    Thread by: 74CJ, Jul 14, 2013, 4 replies, in forum: Intermediate CJ-5/6/7/8
  4. 74CJ
    Post

    Dana 30 problems

    No, I've replaced gear box, tie rod ends repacked my wheel bearings, (replace less than 10k miles ago). The whole axle, springs and even shocks...
    Post by: 74CJ, Aug 18, 2009 in forum: Intermediate CJ-5/6/7/8
  5. 74CJ
    Post

    Dana 30 problems

    Well I installed the upper and lower ball joints and new axle u joints. All that work and it still steers like crap. I noticed as my brother in...
    Post by: 74CJ, Aug 18, 2009 in forum: Intermediate CJ-5/6/7/8
  6. 74CJ
    Post

    Dana 30 problems

    Thanks everyone for the advice and instruction. I've got just about everything, just waiting for what I had to order on line.
    Post by: 74CJ, Aug 11, 2009 in forum: Intermediate CJ-5/6/7/8
  7. 74CJ
    Post

    Dana 30 problems

    I've replaced the wheel bearings and races both inner and outer along with the seals for them. I know how to get that far again, are there any...
    Post by: 74CJ, Aug 10, 2009 in forum: Intermediate CJ-5/6/7/8
  8. 74CJ
    Thread

    Dana 30 problems

    Does anyone tell me the proper procedure to replace the u joints on the d 30 axle, Mine appear to be wore. One thing is I want to have all the...
    Thread by: 74CJ, Aug 10, 2009, 41 replies, in forum: Intermediate CJ-5/6/7/8
  9. 74CJ
    Post

    74 CJ5 seats

    I agree with Boyink on the Bestop seats. I put a set in my 5. Took some getting used to with that bar in the back. Not near as comfortable as...
    Post by: 74CJ, Aug 12, 2008 in forum: Intermediate CJ-5/6/7/8
  10. 74CJ
    Post

    My first jeep

    Welcome from Upstate NY
    Post by: 74CJ, Jul 21, 2008 in forum: Intermediate CJ-5/6/7/8
  11. 74CJ
    Post

    No horn or turn signals

    I found my problem last night finally. It was a short where the wire went through the frame heading up to the right rear tail light. Of course...
    Post by: 74CJ, Jul 13, 2008 in forum: Intermediate CJ-5/6/7/8
  12. 74CJ
    Post

    No horn or turn signals

    It's not quite there but I making some headway. Yes it is a GM column. It does have a 4way pull switch, and that works. The horn now works,...
    Post by: 74CJ, Jul 9, 2008 in forum: Intermediate CJ-5/6/7/8
  13. 74CJ
    Post

    No horn or turn signals

    For the record, all the electrical has worked fine for 3 yrs.
    Post by: 74CJ, Jul 7, 2008 in forum: Intermediate CJ-5/6/7/8
  14. 74CJ
    Post

    No horn or turn signals

    Horn works now. Still no turn signals. I have everything ground about 3 different ways. Gotta get a voltage sensor and start checking...
    Post by: 74CJ, Jul 7, 2008 in forum: Intermediate CJ-5/6/7/8
  15. 74CJ
    Thread

    No horn or turn signals

    I need some help. I have a 74 cj5 that I built about 3 years ago. It has a fiberglass tub and fenders, and a painless wiring harness. I have...
    Thread by: 74CJ, Jul 6, 2008, 11 replies, in forum: Intermediate CJ-5/6/7/8
  16. 74CJ
    Post

    Clutch lever help

    Sounds like the throwout bearing is going bad.
    Post by: 74CJ, Jun 22, 2008 in forum: Intermediate CJ-5/6/7/8
  17. 74CJ
    Post

    Gun Rack in a CJ

    I like it. It is similar to mine but I have mine so the gun rests just above the wheel wells. Pain in the butt to get to when you have stuff in...
    Post by: 74CJ, Jun 17, 2008 in forum: Intermediate CJ-5/6/7/8
  18. 74CJ
    Post

    Gun Rack in a CJ

    I'm always looking for new ideas. I'd like to see the pictures.
    Post by: 74CJ, Jun 15, 2008 in forum: Intermediate CJ-5/6/7/8
  19. 74CJ
    Post

    Distributor install Tips?

    Yes, I forgot to mention, you do need the 8mm wires.
    Post by: 74CJ, Apr 9, 2008 in forum: Intermediate CJ-5/6/7/8
  20. 74CJ
    Post

    Distributor install Tips?

    After pulling mine in and out 4 or 5 times this past weekend, I've gotten pretty good at it. With a cool engine of course pull the #1 plug and...
    Post by: 74CJ, Apr 9, 2008 in forum: Intermediate CJ-5/6/7/8
Showing results 1 to 20 of 98 Next >
Search Again
Page 1 of 5
New Posts