1. Registration trouble? Please use the "Contact Us" link at the bottom right corner of the page and your issue will be resolved.
    Dismiss Notice

Recent Content by ralf

  1. ralf
    Post

    Keep or ditch 6v system

    Both my 2A's are 6 Volt as they came that way. I did get a 6 volt alternator for one of them.
    Post by: ralf, Aug 19, 2012 in forum: Flat Fender Tech
  2. ralf
    Thread

    Info and pics of dual wheel adapters

    I am looking for info and pics of dual wheel adapters for an article I would like to post here and on other Jeep sites.
    Thread by: ralf, Aug 13, 2012, 0 replies, in forum: Flat Fender Tech
  3. ralf
    Post

    Seatbelts in a vintage flattie???

    I am going to use these [IMG]
    Post by: ralf, Aug 5, 2012 in forum: Flat Fender Tech
  4. ralf
    Post

    Gas Pedel To Carb Linkage

    Do a search on the CJ2A forum and you will find a lot of info.
    Post by: ralf, Jul 18, 2012 in forum: Flat Fender Tech
  5. ralf
    Post

    Brake opinion

    I did the swap you mentioned. I found the 10" self adjustors on the front axle of a 60's Jeepster.
    Post by: ralf, Jul 18, 2012 in forum: Flat Fender Tech
  6. ralf
    Post

    need new tires for the flatty

    Eventually they will be back but the tires will be made in China.
    Post by: ralf, Feb 16, 2012 in forum: Flat Fender Tech
  7. ralf
    Post

    yj spring swap

    If you go to the last page of the Holbrook site they give some dimensions that could be helpful.
    Post by: ralf, Feb 5, 2012 in forum: Flat Fender Tech
  8. ralf
    Post

    Dashboards

    The dash is structural so an overlay makes more sense. I completely removed a hacked up one by drilling out all of the spot welds and welding in...
    Post by: ralf, Feb 5, 2012 in forum: Flat Fender Tech
  9. ralf
    Post

    yj spring swap

    http://www.earlycj5.com/technical/springs-and-shocks/earlyintermediate-cj-5-to-wrangleryj-spring-conversion/...
    Post by: ralf, Feb 4, 2012 in forum: Flat Fender Tech
  10. ralf
    Post

    Dual Master Cylinder

    Use Herms bracket but the MC he sold we was way too big, just buy his bracket Cardone has a smaller one that will fit and then use 90 degree banjo...
    Post by: ralf, Jan 27, 2012 in forum: Flat Fender Tech
  11. ralf
    Post

    skinny springs on wide pads

    Check out the wanted section of the CJ2A forum. I am sure there are a lot of them around to be had cheap. $8 to $12 on Epay
    Post by: ralf, Jan 16, 2012 in forum: Flat Fender Tech
  12. ralf
    Post

    rocker guards

    I ordered the steel today for the YJ rocker guards. They found a "drop" so I didn't have to buy a full sheet of 1/4" plate. They are going to...
    Post by: ralf, Jan 5, 2012 in forum: Flat Fender Tech
  13. ralf
    Post

    rocker guards

    I AM GOING TO PUT SOME ON MY YJ. Very simple, 16" wide sheet of 1/4 inch steel plate the length from wheel well to wheel well. I will have the...
    Post by: ralf, Jan 2, 2012 in forum: Flat Fender Tech
  14. ralf
    Post

    brakes on willys

    [IMG]
    Post by: ralf, Dec 4, 2011 in forum: Flat Fender Tech
New Posts