1. Registration trouble? Please use the "Contact Us" link at the bottom right corner of the page and your issue will be resolved.
    Dismiss Notice

Recent Content by timing light

  1. timing light
    Post

    Running Poorly At Idle

    when you has a miss or idle problems, one of two things--ign.electical or carb. if your distributor is old, governor weights holes have ovaled...
    Post by: timing light, May 16, 2016 in forum: Early CJ5 and CJ6 Tech
  2. timing light
    Post

    Picked this up recently

    that's my brothers trailer,he wondered what happened to it. ----------------just kidding. give us some more shots without the carpet camo
    Post by: timing light, Dec 4, 2010 in forum: Jeep Trailer Tech
  3. timing light
    Post

    Need Carb help

    that's high pressure to low, not vacum. i said in the carb.
    Post by: timing light, Oct 10, 2010 in forum: Early CJ5 and CJ6 Tech
  4. timing light
    Post

    Need Carb help

    not to test you , but you tell me , what would make a carb. a vacum chamber?
    Post by: timing light, Oct 10, 2010 in forum: Early CJ5 and CJ6 Tech
  5. timing light
    Post

    Need Carb help

    Yankeefist. if you what my help, contact me. I worked for Rochester Products for 19 yrs. then 22 for the company that bought all their tooling,...
    Post by: timing light, Oct 10, 2010 in forum: Early CJ5 and CJ6 Tech
  6. timing light
    Post

    Need Carb help

    old time called these main jets, they are metering screws-- example, #51 is good from sea level to 4000 ft. above sea level, he is giving you good...
    Post by: timing light, Oct 6, 2010 in forum: Early CJ5 and CJ6 Tech
  7. timing light
    Post

    Need Carb help

    when you have your carb. apart check all your mating surfaces for warpage before going forward. use a good straigth edge. more than likey your...
    Post by: timing light, Oct 6, 2010 in forum: Early CJ5 and CJ6 Tech
  8. timing light
    Post

    Need Carb help

    sorry for the double post, thought the first one didn't enter
    Post by: timing light, Oct 4, 2010 in forum: Early CJ5 and CJ6 Tech
  9. timing light
    Post

    Need Carb help

    ok,i guess my last post was'ntwhat you were looking for. HESTITATION, the duration spring- if you did not replace it, if it's old it's weak- to...
    Post by: timing light, Oct 3, 2010 in forum: Early CJ5 and CJ6 Tech
  10. timing light
    Post

    Need Carb help

    ok, i guess my last post was'nt what you for ask for. HESTITION, the duration spring , if old & weak, will result in slow fuel discharge causing...
    Post by: timing light, Oct 3, 2010 in forum: Early CJ5 and CJ6 Tech
  11. timing light
    Post

    Need Carb help

    first,did you do a major or just a repair carb kit-- either or, did you replace every thing with the new parts? did you completly remove all the...
    Post by: timing light, Oct 3, 2010 in forum: Early CJ5 and CJ6 Tech
  12. timing light
    Post

    Throw out bearing??

    what nickmil said, what i meant, was the throw out bearing centering itself on the pressure plate
    Post by: timing light, Oct 3, 2010 in forum: Early CJ5 and CJ6 Tech
  13. timing light
    Post

    Throw out bearing??

    is your pressure plate on center?
    Post by: timing light, Oct 2, 2010 in forum: Early CJ5 and CJ6 Tech
  14. timing light
    Post

    Need Carb help

    using a vacum guage and sitting for the highest vacum can cause hesitation. your engine must be @ full operating temp. or you CAN NOT adjust the...
    Post by: timing light, Oct 2, 2010 in forum: Early CJ5 and CJ6 Tech
  15. timing light
    Post

    Grommets

    National Rubber,Betel Park, Pa. phone 412-831-6100--- Nationalrubber.co.uk--- they have it all, even military
    Post by: timing light, Sep 26, 2010 in forum: Early Jeep Restoration and Research
New Posts