1. Registration trouble? Please use the "Contact Us" link at the bottom right corner of the page and your issue will be resolved.
    Dismiss Notice

Recent Content by rkusa

  1. rkusa
    Post

    Throw Out Bearing ....and more!

    Also Thanks for that.....That's also why I'm asking.....had I asked before messing with the fork and cable.....I might not have needed to remove...
    Post by: rkusa, Sep 11, 2007 in forum: Early CJ5 and CJ6 Tech
  2. rkusa
    Post

    Throw Out Bearing ....and more!

    Thanks for the great and less expensive idea. I'm doing this in a dirt driveway, so the wheels on whatever jack might be a problem....I'm also...
    Post by: rkusa, Sep 11, 2007 in forum: Early CJ5 and CJ6 Tech
  3. rkusa
    Post

    Throw Out Bearing ....and more!

    Thanks for the advice....I'll do the floor jack thing. I need one more then a tranny jack and they are so much less money. I also don't need to...
    Post by: rkusa, Sep 10, 2007 in forum: Early CJ5 and CJ6 Tech
  4. rkusa
    Post

    Throw Out Bearing ....and more!

    Thanks for the parts places.....Krage's seems to have lots of photos.....since I'm still learning that seems good. I will be attempting the trans...
    Post by: rkusa, Sep 9, 2007 in forum: Early CJ5 and CJ6 Tech
  5. rkusa
    Post

    Throw Out Bearing ....and more!

    Got it out, no problem...and no springs etc.....Great.and Thanks...... Any one have any idea were is the best place to get a clutch fork for 1971...
    Post by: rkusa, Sep 9, 2007 in forum: Early CJ5 and CJ6 Tech
  6. rkusa
    Thread

    Throw Out Bearing ....and more!

    I have worked on this Jeep since Feb....and things were moving forward ......the engine working real good etc. Then.....after taking it for the...
    Thread by: rkusa, Sep 8, 2007, 14 replies, in forum: Early CJ5 and CJ6 Tech
  7. rkusa
    Post

    Help with Dist Cap

    OK....Well I sand blasted the entire underside of the Jeep.....sure wish I could take the body off, but .....I just don't have the equipment yet....
    Post by: rkusa, Jul 31, 2007 in forum: Early CJ5 and CJ6 Tech
  8. rkusa
    Post

    gear advice

    I have a Cj5 stock 1971 with Dana 27a Front end, and I think Dana 44 rear. It came with 265x 7515 tires....I don't know much yet. Are these...
    Post by: rkusa, Jul 23, 2007 in forum: Intermediate CJ-5/6/7/8
  9. rkusa
    Post

    Help with Dist Cap

    Manual is my next tool..... I found the vapor lock problem and fixed it. My fuel line was to close to the engine. Also, my heater hoses feel...
    Post by: rkusa, Jun 16, 2007 in forum: Early CJ5 and CJ6 Tech
  10. rkusa
    Post

    Help with Dist Cap

    Wheel bearings , king pin bearings and more I don't want to take this all apart like you said, until I know at least what to look for and know...
    Post by: rkusa, Jun 15, 2007 in forum: Early CJ5 and CJ6 Tech
  11. rkusa
    Post

    Help with Dist Cap

    Thanks: I had it up for two days, and got rid of all the old grease. I didn't take it apart yet. On the drivers side, the 12 and 6 movement is...
    Post by: rkusa, Jun 15, 2007 in forum: Early CJ5 and CJ6 Tech
  12. rkusa
    Post

    Help with Dist Cap

    No problem with that,or anything for that matter that would be helpful. I know I seem like an info hog, but eventually I'll be on the other side...
    Post by: rkusa, Jun 15, 2007 in forum: Early CJ5 and CJ6 Tech
  13. rkusa
    Post

    Help with Dist Cap

    Dana 27A King Pin and wheel bearing That sounds great. So I have the entire front axle about clean now. So do I just start by removing...
    Post by: rkusa, Jun 14, 2007 in forum: Early CJ5 and CJ6 Tech
  14. rkusa
    Post

    Help with Dist Cap

    OK I went to NAPA and they can get Kingpins for about $100 bucks. I also wonder if a DANA 30 from a 1984 CJ7 with disk breaks axle and springs...
    Post by: rkusa, Jun 13, 2007 in forum: Early CJ5 and CJ6 Tech
New Posts