1. Registration trouble? Please use the "Contact Us" link at the bottom right corner of the page and your issue will be resolved.
    Dismiss Notice

Dual Solenoid Winch Wiring (bellview)

Discussion in 'Winches' started by Long&Low, Oct 11, 2011.

  1. Sep 22, 2014
    tarry99

    tarry99 Member

    Northern California
    Joined:
    Oct 29, 2012
    Messages:
    3,784
    John , here you go on a quick drawing............the solenoids and switch suggestions are just that! I have the old Warn Bellview style Winch also but I'm not really sure of the Amperage rating on that motor.........Herm sells the motors so he may know , I will try to figure out what Solenoids I used but there old and I see no numbers. Do your Homework on sourcing. The Bosch Solenoid mentioned below should be fine.

    Corrected Drawing Sorry about that!

    [​IMG]
     
    Last edited: Sep 23, 2014
  2. Sep 22, 2014
    45es

    45es Active Member 2024 Sponsor 2023 Sponsor 2022 Sponsor

    Buckley, WA
    Joined:
    Mar 31, 2007
    Messages:
    1,151
  3. Sep 22, 2014
    oddfirejeeper

    oddfirejeeper Active Member

    Hamilton, MI
    Joined:
    May 5, 2004
    Messages:
    1,253
    thanks for the pictures 45es. that is a really clean looking install.
     
  4. Sep 22, 2014
    Walt Couch

    Walt Couch 07/02/40 - 10/27/24 RIP

    cordele, Ga.
    Joined:
    Mar 29, 2007
    Messages:
    5,949
    terry99 your 3 switches should be connected to power instead of grounds. You have no power to activate the solenoids.
     
  5. Sep 22, 2014
    oddfirejeeper

    oddfirejeeper Active Member

    Hamilton, MI
    Joined:
    May 5, 2004
    Messages:
    1,253
    this may sound silly but if i remember right there is an "s" and an "I" on the two little posts i believe you hook the trigger wire to the "I" right? i never seen a ground run from either small post i thought it grounded itself with the bracket.
     
  6. Sep 22, 2014
    oddfirejeeper

    oddfirejeeper Active Member

    Hamilton, MI
    Joined:
    May 5, 2004
    Messages:
    1,253
    i wound the cable onto the winch tonight and i cannot believe how fast that thing is. i had an old wind up winch with some large cable on it and after 15 minutes of unwinding it i found it was too big for the winch. spent another 15 minutes winding it back on and took off the other cable from the other winch.
     
  7. Sep 22, 2014
    Walt Couch

    Walt Couch 07/02/40 - 10/27/24 RIP

    cordele, Ga.
    Joined:
    Mar 29, 2007
    Messages:
    5,949
    Diff solenoids for diff jobs. A starter type solenoid will have the "S" to the starter term on ignition switch and the "I" will go to the + coil for ign bypass.
    Other heavy duty solenoids can come with only one small terminal for power "ON" and the solenoid coil is internally grounded.
    Other solenoids have two small terminals unmarked so one requires power and the other a wire to ground.
     
  8. Sep 22, 2014
    tarry99

    tarry99 Member

    Northern California
    Joined:
    Oct 29, 2012
    Messages:
    3,784
    Hey Walt..............I said it was quick! You're right power on the side of the switch I had marked Ground...............DUH! Drawing is now Correct
     
    Last edited: Sep 23, 2014
  9. Jun 15, 2021
    jeeper50

    jeeper50 jeeps 'till I die

    Spanish Fort. AL
    Joined:
    Dec 20, 2007
    Messages:
    844
    Thank you for moving this for future useage
     
New Posts