1. Registration trouble? Please use the "Contact Us" link at the bottom right corner of the page and your issue will be resolved.
    Dismiss Notice

Search Results

Search Again
Page 1 of 2
  1. GarageBoy
    Post

    Best books for restoration?

    Where do I get the FSM? Also, there was a reccomendation made by jeeps unlimited before the site went over. What was it?
    Post by: GarageBoy, Aug 22, 2006 in forum: Intermediate CJ-5/6/7/8
  2. GarageBoy
    Thread

    Best books for restoration?

    What books do you guys recommend for a guy trying to tear down a CJ5 and do a complete resto? Thanks
    Thread by: GarageBoy, Aug 19, 2006, 6 replies, in forum: Intermediate CJ-5/6/7/8
  3. GarageBoy
    Post

    '47 CJ2A engine options?

    The 4.3L V6 from Chevrolet will fit.
    Post by: GarageBoy, Jul 16, 2006 in forum: Flat Fender Tech
  4. GarageBoy
    Post

    Building a flatfender replica..

    Thanks Warloch! Can I PM you if anything?
    Post by: GarageBoy, Jul 5, 2006 in forum: Flat Fender Tech
  5. GarageBoy
    Post

    Building a flatfender replica..

    Thanks Warloch! Are 18 and 20s interchangable? Also, are 4.88s considered high or low for a Jeep? I'm used to muscle cars running no lower than 4.56
    Post by: GarageBoy, Jul 5, 2006 in forum: Flat Fender Tech
  6. GarageBoy
    Post

    Building a flatfender replica..

    I like V8s too, but too much engine for the vehicle. Will the 4.3L V6 and the NV3500 fit in the Willys platform? I'd like to run a 5 Speed, but 4...
    Post by: GarageBoy, Jul 3, 2006 in forum: Flat Fender Tech
  7. GarageBoy
    Post

    Building a flatfender replica..

    Thanks! I didnt know there's so much support for the CJ2/3s..(quadratec doesn't stock much)
    Post by: GarageBoy, Jun 27, 2006 in forum: Flat Fender Tech
  8. GarageBoy
    Post

    Building a flatfender replica..

    I'm going with the 4.3 V6, might wanna back it up with an overdrive tranny (still looking into my options). Now, where to get suspension parts?...
    Post by: GarageBoy, Jun 24, 2006 in forum: Flat Fender Tech
  9. GarageBoy
    Post

    Building a flatfender replica..

    I'm not sure what 3 speed I have in the 75, but if it's original, it's a T14 tranny, and stock Dana 30/44 diffs. How's the MOPAR I4 they used in...
    Post by: GarageBoy, Jun 24, 2006 in forum: Flat Fender Tech
  10. GarageBoy
    Post

    Building a flatfender replica..

    What tranny are you running, Warloch? I'm getting a new frame all together.. then getting the willys overland complete body kit. We wanna do a...
    Post by: GarageBoy, Jun 23, 2006 in forum: Flat Fender Tech
  11. GarageBoy
    Post

    Hello! New dude with a rotted out 75 CJ5..

    Short wheelbase is fine. There's already a 2005 Wrangler for everything else. This was gonna be a fun show car
    Post by: GarageBoy, Jun 23, 2006 in forum: Intermediate CJ-5/6/7/8
  12. GarageBoy
    Post

    Building a flatfender replica..

    The 4.3L V6 will fit? in a CJ2? (Will a SBC fit?) I still need to hunt down a tranny/transfercase/OD unit.. Thanks
    Post by: GarageBoy, Jun 23, 2006 in forum: Flat Fender Tech
  13. GarageBoy
    Thread

    Building a flatfender replica..

    Ok, my buddy has a rotted out 75 CJ5 (rotted down to the frame) Instead, he would rather ditch the whole thing and build a CJ2A/MB replica with a...
    Thread by: GarageBoy, Jun 23, 2006, 26 replies, in forum: Flat Fender Tech
  14. GarageBoy
    Post

    Hello! New dude with a rotted out 75 CJ5..

    Also, since we found flat fendered frames, he's gonna go that route..(with a modern drive train)
    Post by: GarageBoy, Jun 23, 2006 in forum: Intermediate CJ-5/6/7/8
  15. GarageBoy
    Post

    Hello! New dude with a rotted out 75 CJ5..

    How are http://www.matkinsextreme.com/Jeeps/Bro1.htm or http://www.nejeeps.com/frameprice.html or should I get the ones quadratec sells for...
    Post by: GarageBoy, Jun 22, 2006 in forum: Intermediate CJ-5/6/7/8
  16. GarageBoy
    Post

    Hello! New dude with a rotted out 75 CJ5..

    Does the I6 have aftermarket support ? (can I get aftermarket FI, etc from like, Holley, Edelbrock, etc?)
    Post by: GarageBoy, Jun 22, 2006 in forum: Intermediate CJ-5/6/7/8
  17. GarageBoy
    Post

    Hello! New dude with a rotted out 75 CJ5..

    Well, you guys told me, they're all pretty much bad mileage wise..so I'm going to stick with the I6. If I were to convert it over to the 4.3L V6...
    Post by: GarageBoy, Jun 21, 2006 in forum: Intermediate CJ-5/6/7/8
  18. GarageBoy
    Post

    Hello! New dude with a rotted out 75 CJ5..

    Thanks! My buddy is willing to go all out and save a few headaches on the chassis, I remember there being new ones made (quadratec has em for...
    Post by: GarageBoy, Jun 21, 2006 in forum: Intermediate CJ-5/6/7/8
  19. GarageBoy
    Post

    Hello! New dude with a rotted out 75 CJ5..

    4.3L what? Chevy V6? If I were to go that route, I just might as well go full SBC. What should the stock engine tranny, transfer case, etc be...
    Post by: GarageBoy, Jun 21, 2006 in forum: Intermediate CJ-5/6/7/8
  20. GarageBoy
    Post

    Hello! New dude with a rotted out 75 CJ5..

    Every major thing has some rot on it..(the windsheild frame is separating from the top) The yellow paint basically hides everything.. Tail gate...
    Post by: GarageBoy, Jun 20, 2006 in forum: Intermediate CJ-5/6/7/8
Showing results 1 to 20 of 22 Next >
Search Again
Page 1 of 2
New Posts