1. Registration trouble? Please use the "Contact Us" link at the bottom right corner of the page and your issue will be resolved.
    Dismiss Notice

Search Results

Search Again
  1. Makngtrax
    Post

    Up to date pics of the M38

    Nice Job !!
    Post by: Makngtrax, Jul 30, 2008 in forum: Flat Fender Tech
  2. Makngtrax
    Post

    F-Head into an MB

    No Problem, Here's the 3B link if you haven't been there yet. J.R. http://www.film.queensu.ca/CJ3B/Tech/LowHoodFHead.html
    Post by: Makngtrax, Jul 29, 2008 in forum: Flat Fender Tech
  3. Makngtrax
    Post

    F-Head into an MB

    Kman, I forgot about this on the 2A page. A couple of photos of some........................linkage :) J.R....
    Post by: Makngtrax, Jul 28, 2008 in forum: Flat Fender Tech
  4. Makngtrax
    Post

    F-Head into an MB

    Sounds like you have a carb. I think any of the 1900 serries will work the key being the base. I'm about 80 % done putting one on my 3A, (couldn't...
    Post by: Makngtrax, Jul 27, 2008 in forum: Flat Fender Tech
  5. Makngtrax
    Post

    Differences between the M38 and 3A

    Don't forget the passenger side glove box. J.R.
    Post by: Makngtrax, Feb 7, 2007 in forum: Flat Fender Tech
  6. Makngtrax
    Post

    2.8 V6

    Wow, Thanks ! Guess I'll hold out for something better.
    Post by: Makngtrax, Feb 2, 2007 in forum: Flat Fender Tech
  7. Makngtrax
    Thread

    2.8 V6

    I may have found a 2.8 V6 out of an Chevy S10, any thoughts on this motor? Thanks, J.R.
    Thread by: Makngtrax, Feb 1, 2007, 14 replies, in forum: Flat Fender Tech
  8. Makngtrax
    Post

    V6 Id

    Thanks, The search continues. It turned out to be a 2.8 FWD out of a 90 something Buick. Thanks again, J.R.
    Post by: Makngtrax, Jan 31, 2007 in forum: Flat Fender Tech
  9. Makngtrax
    Thread

    V6 Id

    I found a GM V6 but the guy that has it isn't sure what it is. What should I look for so I don't get one of the FWD ones I can't use? By the...
    Thread by: Makngtrax, Jan 29, 2007, 3 replies, in forum: Flat Fender Tech
  10. Makngtrax
    Post

    v6 swap

    Thanks, That helped alot. I guess I'll have to see what type of deal I can come across on what and go from there. J.R.
    Post by: Makngtrax, Jan 27, 2007 in forum: Flat Fender Tech
  11. Makngtrax
    Post

    v6 swap

    Greetings, I'm somewhat new here and have a flat fender frankenjeep project I hope to get started on in the near future. The 225's/231's...
    Post by: Makngtrax, Jan 27, 2007 in forum: Flat Fender Tech
  12. Makngtrax
    Post

    Frame Paint

    Hi, I saw this discussion a whlie back on one of the other forums around, 2A maybe, Anyway, it was sugjested to use the black from a Case...
    Post by: Makngtrax, Dec 17, 2005 in forum: Early Jeep Restoration and Research
Showing results 1 to 12 of 12
Search Again
New Posts