1. Registration trouble? Please use the "Contact Us" link at the bottom right corner of the page and your issue will be resolved.
    Dismiss Notice

Recent Content by ardan

  1. ardan
    Post

    Noise In The Front Of The Engine

    Just wanted and post an update and thank everyone again for all the help and advise... I just passed my first 100 Miles and everything is still...
    Post by: ardan, Jul 13, 2020 in forum: Flat Fender Tech
  2. ardan
    Post

    Noise In The Front Of The Engine

    Hi Guys, Well, I finally had a good day. I replaced the front pulley with a new one and the noise is gone. There must have been something...
    Post by: ardan, Mar 6, 2020 in forum: Flat Fender Tech
  3. ardan
    Post

    Noise In The Front Of The Engine

    HI Guys, I will have to look up "dial indicator", I don't have one for sure. I have had the jeep about a year but it has been being worked on...
    Post by: ardan, Mar 1, 2020 in forum: Flat Fender Tech
  4. ardan
    Post

    Noise In The Front Of The Engine

    Hi All, Thanks for all the ideas. We Pulled the oil pan and the timing cover, after cleaning and checking everything we were careful to put...
    Post by: ardan, Mar 1, 2020 in forum: Flat Fender Tech
  5. ardan
    Post

    Noise In The Front Of The Engine

    Will Do, Thanks...
    Post by: ardan, Feb 29, 2020 in forum: Flat Fender Tech
  6. ardan
    Post

    Noise In The Front Of The Engine

    Hi All, Visually the end of the crank looks OK, I sure hope it is. I have a new pulley ordered so I will post an update next week after it gets...
    Post by: ardan, Feb 29, 2020 in forum: Flat Fender Tech
  7. ardan
    Post

    Noise In The Front Of The Engine

    I didn't pull the timing cover off today, I only the pulley off. I replaced the seal when I removed the timing cover weeks ago while I was...
    Post by: ardan, Feb 29, 2020 in forum: Flat Fender Tech
  8. ardan
    Post

    Noise In The Front Of The Engine

    Hi Guys, Maybe I found something. I pulled the pulley off and found that there is a groove cut in the side of the pulley where it inserts into...
    Post by: ardan, Feb 29, 2020 in forum: Flat Fender Tech
  9. ardan
    Post

    Noise In The Front Of The Engine

    Hi Guys, Just because it is a pretty day I decided to take the plunge and drive it around the block (about 4 Miles). The temp gauge went to 150...
    Post by: ardan, Feb 29, 2020 in forum: Flat Fender Tech
  10. ardan
    Post

    Noise In The Front Of The Engine

    Thanks for the feedback, I will check out some you tube videos on the Front Main Bearing and Cam Bearing and see what they say. The Water...
    Post by: ardan, Feb 29, 2020 in forum: Flat Fender Tech
  11. ardan
    Post

    Noise In The Front Of The Engine

    Hi Guys, Here is this mornings update I cranked it up and let it run while I got prepared to take it down the street. The motor purred like a...
    Post by: ardan, Feb 29, 2020 in forum: Flat Fender Tech
  12. ardan
    Post

    Noise In The Front Of The Engine

    Hi Guys, Be away for a couple of days and didn't see the post. Thanks for all the ideas and comments. Let me update you on where I am now. I...
    Post by: ardan, Feb 28, 2020 in forum: Flat Fender Tech
  13. ardan
    Post

    Noise In The Front Of The Engine

    We rebuild everything but the internals of the engine. We did pull the timing cover and clean it up and replace the gaskets put in new bolts etc....
    Post by: ardan, Feb 22, 2020 in forum: Flat Fender Tech
  14. ardan
    Post

    Noise In The Front Of The Engine

    Yes, Everytime it does 3 or 4 very short grinding (hiccups) and then a few seconds later it is constant from that point on.
    Post by: ardan, Feb 22, 2020 in forum: Flat Fender Tech
  15. ardan
    Post

    Noise In The Front Of The Engine

    The Crank Pulley was bend when I removed it, I was getting ready to order a new one but was trying to go ahead and test it since everything else...
    Post by: ardan, Feb 22, 2020 in forum: Flat Fender Tech
New Posts