1. Registration trouble? Please use the "Contact Us" link at the bottom right corner of the page and your issue will be resolved.
    Dismiss Notice

Recent Content by Jerry M

  1. Jerry M
    Post

    front disk brake conversion opinion

    I have disks on all 4. the best thing I have done, I love them it stop straight and good. If you are off road most of the time drums be okay...
    Post by: Jerry M, Dec 14, 2006 in forum: Early CJ5 and CJ6 Tech
  2. Jerry M
    Post

    single wire alt.....

    If it is a single wire altentor all you need is the one to the batt. jerry
    Post by: Jerry M, Sep 9, 2006 in forum: Intermediate CJ-5/6/7/8
  3. Jerry M
    Post

    TBI on 74 cj5

    I try-ed it out this weekend It ran good at home 300' elev but at 5000' not to good till I hooked up the map senor then it was better but not...
    Post by: Jerry M, Jun 19, 2006 in forum: Intermediate CJ-5/6/7/8
  4. Jerry M
    Post

    TBI on 74 cj5

    Re: TBI on 74 cj I don't know it was not that hard. I got the wiring and went thought and marked all of them. they have a good article I am not...
    Post by: Jerry M, Jun 15, 2006 in forum: Intermediate CJ-5/6/7/8
  5. Jerry M
    Thread

    TBI on 74 cj5

    I just put TBI on my jeep. I took it off a 4.3 van the van was free. i think i am into it about $250 fule pump plate for the tbi. It's run...
    Thread by: Jerry M, Jun 15, 2006, 4 replies, in forum: Intermediate CJ-5/6/7/8
  6. Jerry M
    Post

    5bolt hubs to 6 bolts...

    i think you have to change everything which maens drum brakes. jerrry
    Post by: Jerry M, May 25, 2006 in forum: Intermediate CJ-5/6/7/8
  7. Jerry M
    Post

    disc brake swap, donor scout??

    When I did mine All used off a scout was the Rotors. Jerry
    Post by: Jerry M, May 25, 2006 in forum: Intermediate CJ-5/6/7/8
  8. Jerry M
    Post

    disc brake proportioning valve..

    Re: disk brake proportioning valve.. When I put the disk on my cj5 I had to take the check value out of the M C and on the front they worked....
    Post by: Jerry M, May 19, 2006 in forum: Intermediate CJ-5/6/7/8
  9. Jerry M
    Post

    master cylinder change

    I went to the napa store and found one that would mount up with a bigger boar size I think I went from 15/16 to 1 1/8 made a big difference....
    Post by: Jerry M, Mar 20, 2006 in forum: Intermediate CJ-5/6/7/8
  10. Jerry M
    Post

    Front Seats

    that what I think I want more leg room. I might cut the wheel well out so I move it back more . What is PRP jerry
    Post by: Jerry M, Mar 14, 2006 in forum: Intermediate CJ-5/6/7/8
  11. Jerry M
    Post

    Front Seats

    what kind of seats are they I want something that is comfortable and that I can get out of and my wife can get out of jerry
    Post by: Jerry M, Mar 14, 2006 in forum: Intermediate CJ-5/6/7/8
  12. Jerry M
    Post

    Shortening Steering Shaft

    I shorten mine I think I cut 5" out it so much nicer I just cut it and took a piece out and weld it back together then shorten the tube. Jerry
    Post by: Jerry M, Feb 16, 2006 in forum: Intermediate CJ-5/6/7/8
  13. Jerry M
    Post

    let's talk about 4.3 engines in Jeeps

    Can a preson take a throttle body and computer off a 4.3 and put it on a 258 Jerry
    Post by: Jerry M, Feb 14, 2006 in forum: Intermediate CJ-5/6/7/8
  14. Jerry M
    Post

    sore elbow

    My old door I made rod that went in a hole and held the door shut but they were just half door so you could reach over the top to open. I have a...
    Post by: Jerry M, Feb 13, 2006 in forum: Intermediate CJ-5/6/7/8
New Posts