1. Registration trouble? Please use the "Contact Us" link at the bottom right corner of the page and your issue will be resolved.
    Dismiss Notice

different jeep or new engine/tranny?

Discussion in 'Early CJ5 and CJ6 Tech' started by unclebill, May 23, 2010.

  1. dnb71R2

    dnb71R2 SuperDave 2023 Sponsor

    Yes - great news!
    Does this mean you are going to cancel the Craigslist ad?
     
  2. ChopperDoc

    ChopperDoc New Member

    unclebill, pm sent
     
  3. duffer

    duffer Rodent Power

    I see it now, sbc/sm465- Waaaaaahoooooooooooo. Rat rod II-but will require a rechristening
     
  4. unclebill

    unclebill Banned

    yep

    i was theatening to kick the slug out.
    trying to scare him into behaving.
    that tuff love stuff ya know?
     
  5. rusty

    rusty Well-Known Member

    Glad your keeping the Slug. This is an amazing site, with even more amazing members. :)
     
  6. SmokinIdahoan

    SmokinIdahoan Avian Flu Controller

    I'm glad youre keeping the slug, i'd hate to have to re-write the song all because you had a new jeep with a new name....although, with the upgrade to a v6, might have to add something to the name...maybe like super slug or something? maybe we could find someone really good at artistry and you could have your own super slug logo - like mopar used in the late 60's/early 70's with the roadrunner :D
     
  7. Warloch

    Warloch Did you say Flattie??? Staff Member

    You will need to think about what you want to end up with. Like many here have said, the T98 with the 4cyl is highly sought after and could go a long ways to paying for what you need. I have T90's out the wazoo and 2 SM465s sitting on the floor with only one spoken for.

    Saginaw with the right parts takes me a weekend to put in, I have 11" brakes on shelves...
     
  8. dnb71R2

    dnb71R2 SuperDave 2023 Sponsor

    The new name could be SPEEDY SLUG !
    Like Matt said - get a little logo ... of a slug spinning its wheels doing a burn out.
     
  9. garage gnome

    garage gnome ECJ5 welder

    Great news!

    Just one question, was the t-98 an option for the CJ5's?

    Poor, poor F-head, another one off to the scrape yard....
     
  10. timgr

    timgr We stand on the shoulders of giants. 2022 Sponsor

    Yes, with the F134 only.
     
  11. garage gnome

    garage gnome ECJ5 welder

    sounds like it is a rare option to me. Then I wouldn't put a different engine in. Leave it as a original rare piece.
     
  12. timgr

    timgr We stand on the shoulders of giants. 2022 Sponsor

    To Bill, A T-18 would fit nicely under your existing floor plates. If it were mine and I were in your position, I'd go with a J-truck T-18 and a Buick V6. I'd let Chuck choose the engine... my choice might not be the same as his, but his opinion is important for obvious reasons.

    The T-98 and F134 are worth something as a unit, but they would be worth more if they came with the floor plates. If you switch to a T-90, it will be easier to shift and you can sell the floor plates along with the engine and transmission.
     
  13. timgr

    timgr We stand on the shoulders of giants. 2022 Sponsor

    Well, they aren't "rare" like Duesenbergs are rare. I would guess the number of them still in existence is more than 10,000. So not rare based on numbers alone.
     
  14. Patrick

    Patrick Super Moderator Staff Member

    Why would a T90 be easier to shift?

    IMO, removing a 4 speed and putting in a 3 speed is regression.
    Especially where Bill lives.
     
  15. timgr

    timgr We stand on the shoulders of giants. 2022 Sponsor

    Because a B-W 3-speed is easier to shift than a truck 4-speed. Certainly it makes a difference in stop-and-go traffic. A T-15 would be even better.

    I agree though - I would stick with a 4-speed.
     
  16. Patrick

    Patrick Super Moderator Staff Member

    Honestly I haven't experienced that. :shrug:
     
  17. unclebill

    unclebill Banned

    it's gotta be a 4 speed.
    the gearing i have now is really nice on the trails.
    going down steep inclines.
    i dont have to use the brakes!
     
  18. jasonjp62

    jasonjp62 Member

    Doesn't novak make an adapter for the t98 to a gm motor?
    Posted via Mobile Device
     
  19. colojeepguy

    colojeepguy Colorado Springs

    A T90 has a non-synchroed 1st gear, so it's actually a little more of a challenge to drive around town (the 4 speed would have a non-synchro 1st gear also, but being a granny gear you wouldn't use it in normal driving) Lots of times I find myself lugging my T90 in 2nd when it would really be better to go down to 1st, just cause I'm too lazy to double clutch it-easier to let the 225's torque get the job done.
     
  20. Warloch

    Warloch Did you say Flattie??? Staff Member

    Talking with Bill - I will focus on trying to get a T18 to put in it, but those are tough to find here abouts. The SM465 would be a backup plan. I would also recommend keeping the floor plates together, I have several to cut and build with to make a custom one fit.

    ChopperDoc in Aurora has offered up a motor that just needs to be built, so when I get it from him, Bill and I will talk pros and cons as I have 2 231's with fresh builds on them sitting on stands (with 4bbl Edelbrock intakes on them).

    Heck - I have a T14, D18, OD sitting on a shelf as well.