1. Registration trouble? Please use the "Contact Us" link at the bottom right corner of the page and your issue will be resolved.
    Dismiss Notice

Corner Patch Panels

Discussion in 'Early CJ5 and CJ6 Tech' started by colojeepguy, Jun 13, 2021.

  1. Jun 13, 2021
    colojeepguy

    colojeepguy Colorado Springs

    At the foot of...
    Joined:
    Apr 4, 2010
    Messages:
    7,179
    Does anyone make corner patch panels for a CJ?
    20210612_101030.jpg
     
    colojeepguy, Jun 13, 2021
    #1
  2. Jun 13, 2021
    FinoCJ

    FinoCJ 1970 CJ5 Staff Member

    Bozeman, MT
    Joined:
    Jul 18, 2013
    Messages:
    5,652
    I couldn't find any a couple months ago. I ended up buying the whole rear side panel from classic enterprise as I couldn't get just the corner...they do sell just the bottom of the corner, but depends on how high up the repair goes...I plan to cover my repair work with the corner armor from warrior...
     
    FinoCJ, Jun 13, 2021
    #2
    colojeepguy likes this.
  3. Jun 13, 2021
    FinoCJ

    FinoCJ 1970 CJ5 Staff Member

    Bozeman, MT
    Joined:
    Jul 18, 2013
    Messages:
    5,652
    FinoCJ, Jun 13, 2021
    #3
    Rodney likes this.
  4. Jun 13, 2021
    garage gnome

    garage gnome ECJ5 welder

    Western MA
    Joined:
    Jun 19, 2009
    Messages:
    3,093
    For that patch, just take a piece of sheetmetal and bend it to form the radius. I think 4” pvc pipe is correct for the radius.
     
    garage gnome, Jun 13, 2021
    #4
    Rust Ranger and Rodney like this.
  5. Jun 13, 2021
    tcfeet

    tcfeet Member

    east of west,...
    Joined:
    May 30, 2009
    Messages:
    352
    Yep, I built one using a piece of 4 an 5/8 " od heavy pipe to form the sheet metal around. Used a piece of 16 gauge sheet metal. Took lots of hammering
    but it came out good. Lots stronger than the original. Mine was mangled from the bottom to one inch from the top lip. Looks like yours would be a lot easier as it is lots narrower.
     
    tcfeet, Jun 13, 2021
    #5
    Rust Ranger and Rodney like this.
  6. Jun 13, 2021
    colojeepguy

    colojeepguy Colorado Springs

    At the foot of...
    Joined:
    Apr 4, 2010
    Messages:
    7,179
    I think he's going to get some of those too, but we need to repair that sheetmetal first.
     
    colojeepguy, Jun 13, 2021
    #6
    FinoCJ and Rodney like this.
  7. Jun 13, 2021
    Twin2

    Twin2 not him 2024 Sponsor 2023 Sponsor 2022 Sponsor

    Virginia Beach, VA
    Joined:
    Apr 28, 2011
    Messages:
    5,421
    Twin2, Jun 13, 2021
    #7
    colojeepguy likes this.
  8. Jun 13, 2021
    Rodney

    Rodney Member

    Sierra Foothills
    Joined:
    Jan 9, 2021
    Messages:
    366
    Or you can Armor plate the entire back like I did.
     
    Rodney, Jun 13, 2021
    #8
    Rust Ranger likes this.
  9. Jun 13, 2021
    FinoCJ

    FinoCJ 1970 CJ5 Staff Member

    Bozeman, MT
    Joined:
    Jul 18, 2013
    Messages:
    5,652
    This is my plan...
     
    FinoCJ, Jun 13, 2021
    #9
    Rodney likes this.
  10. Jun 13, 2021
    Dave Deyton

    Dave Deyton Member

    Fuquay-Varina, NC
    Joined:
    Oct 12, 2003
    Messages:
    862
    Beat to the punch. 18 ga. cold rolled sheet steel bent over 4" in PVC pipe. Works real well.
    For the bottom panels, I make a a hammer form. Make a pattern out of Card stock and transfer it to plywood.
    Sandwich the steel between two pieces of plywood and clamp them together. Add extra metal for the flange and hammer the edges slowly around keeping from folding over the metal on itself. Works Great. Look up hammer forming sheet metal.

    Lots of information on the web.

    Dave
     
    Dave Deyton, Jun 13, 2021
    #10
    Rust Ranger, truckee4x4 and Rodney like this.
  11. Jun 13, 2021
    Steve's 70-5

    Steve's 70-5 Active Member

    Louisville, Ky
    Joined:
    Nov 12, 2009
    Messages:
    1,383
    Steve's 70-5, Jun 13, 2021
    #11
    Rodney likes this.
New Posts