1. Registration trouble? Please use the "Contact Us" link at the bottom right corner of the page and your issue will be resolved.
    Dismiss Notice

Replacement oil lines

Discussion in 'Early CJ5 and CJ6 Tech' started by Yooper John, Jun 23, 2015.

  1. Jun 23, 2015
    Yooper John

    Yooper John Member

    Joined:
    Oct 2, 2014
    Messages:
    93
    Well, after going thru everything and replacing all rubber lines, detailing under the hood, etc, the new oil line to the filter blew. This thing is brand new! Made a huge mess, and had I been going down the highway, I wouldn't have known it till the engine locked. I'll let Walcks know about it, but this is pretty ridiculous. Only about 500 miles on it. Anyhow, just venting my frustration.
     
    Yooper John, Jun 23, 2015
    #1
  2. Jun 23, 2015
    Howard Eisenhauer

    Howard Eisenhauer Administrator Staff Member

    Tantallon, Nova...
    Joined:
    Nov 22, 2003
    Messages:
    8,126
    :(

    Did the hose split or did the end blow off?

    H.
     
    Howard Eisenhauer, Jun 23, 2015
    #2
  3. Jun 23, 2015
    47v6

    47v6 junk wrecker! 2023 Sponsor 2022 Sponsor

    USA
    Joined:
    Oct 25, 2006
    Messages:
    5,801
    Thats terrible. glad you didn't kill it.
     
    47v6, Jun 23, 2015
    #3
  4. Jun 23, 2015
    Wenaha

    Wenaha Member

    West Coast
    Joined:
    Feb 6, 2014
    Messages:
    415
    Maybe consider a braided stainless hose? I've running these for oil lines and never a problem.
     
    Wenaha, Jun 23, 2015
    #4
  5. Jun 23, 2015
    Howard Eisenhauer

    Howard Eisenhauer Administrator Staff Member

    Tantallon, Nova...
    Joined:
    Nov 22, 2003
    Messages:
    8,126
    It's only 60 PSI at most. I had a set made up 25 years ago from cloth braided rubber hose & push in fittings- the guy at the hydraulics shop told me they'd be good for 800 PSI.

    Apart from getting a little stiff they still work fine. There has to be a fundamental manufacturing defect with YJ's lines, or they were made with the wrong materials.


    H.
     
    Howard Eisenhauer, Jun 23, 2015
    #5
  6. Jun 23, 2015
    PeteL

    PeteL If it wasn't for physics, and law enforcement... 2024 Sponsor 2023 Sponsor 2022 Sponsor

    Hills of NH
    Joined:
    Aug 3, 2003
    Messages:
    9,831
    Hate to say it but some of Walck's stuff is real junk.
     
    PeteL, Jun 23, 2015
    #6
  7. Jun 23, 2015
    Stout

    Stout Member

    Quakertown, PA
    Joined:
    Nov 1, 2010
    Messages:
    958
    I had a similar problem but mine was totally my own fault -- I routed the oil line too close to the exhaust manifold and it melted. I noticed a lot of smoke coming from under the hood and pulled over. Replaced it with another new rubber line, routed it more carefully, and haven't had a problem since.
     
    Stout, Jun 23, 2015
    #7
  8. Jun 23, 2015
    Yooper John

    Yooper John Member

    Joined:
    Oct 2, 2014
    Messages:
    93
    Hi. I think tomorrow I'll have the hydraulics shop make me two new ones. Pinhole developed about an inch below the fitting at the filter. Not close to anything at all. Not a big deal other than the huge mess, and could have lost an engine on a long trip. I replaced every rubber hose, seal and gasket on the whole thing this winter to prevent these kinds of problems. I'm sure the Crown seals will be next to go in the diffs and transfer case. Anyone remember if the hose ends are 1/8 pipe or inverted flare?
     
    Yooper John, Jun 23, 2015
    #8
  9. Jun 24, 2015
    Yooper John

    Yooper John Member

    Joined:
    Oct 2, 2014
    Messages:
    93
    Walcks has contacted me, and would like the line back, as their manufacturer guaranteed that this won't happen. They will reimburse for shipping and send a replacement. My customer service experiences with them have always been positive.
     
    Yooper John, Jun 24, 2015
    #9
  10. Jun 24, 2015
    47v6

    47v6 junk wrecker! 2023 Sponsor 2022 Sponsor

    USA
    Joined:
    Oct 25, 2006
    Messages:
    5,801
    I have had great experiences with them as well.
     
    47v6, Jun 24, 2015
    #10
  11. Jun 24, 2015
    commanlerwrangdo

    commanlerwrangdo Member

    Cleveland, Ohio
    Joined:
    Feb 10, 2014
    Messages:
    470
    On my Boss' 50 Chevy, I eliminated the rubber oil lines and bent a set out of 1/4" nickel steel lines. I saw no need for "flex" as the canister for the filter is mounted on the intake manifold. Works like a charm and I think it looks better too.
     
    commanlerwrangdo, Jun 24, 2015
    #11
  12. Jul 1, 2015
    Yooper John

    Yooper John Member

    Joined:
    Oct 2, 2014
    Messages:
    93
    FYI, I hade a 48" hydraulic line made with 1/8 pipe at both ends and installed a high pressure 90 to clear the fuel pump, so all is well now.
     
    Yooper John, Jul 1, 2015
    #12
New Posts