1. Registration trouble? Please use the "Contact Us" link at the bottom right corner of the page and your issue will be resolved.
    Dismiss Notice

The Gold Project

Discussion in 'Builds and Fabricators Forum' started by neptco19, Jan 24, 2007.

  1. neptco19

    neptco19 That guy....

    fo shizzle..
     
  2. Andy4802

    Andy4802 Canadian Jeep junkie

    what was the donor of the new rearend?
     
  3. NoFlyZone

    NoFlyZone Member

    53"? thats CJ narrow track width.
     
  4. neptco19

    neptco19 That guy....

    Not sure what the new axle came out of, the guy I got it from had it laying in his field beside a bunch of other junk... Those measurements are from the axle flange to flange.
     
  5. jeepaholic

    jeepaholic Jeepfreak81's fabricator!

    wide track J-truck
     
  6. neptco19

    neptco19 That guy....

    Thanks, that will come in handy when Im looking for spare axle shafts :)
     
  7. neptco19

    neptco19 That guy....

    Alrighty so here is engine #4 (had to go back through the thread and count :( )that is going in....one in it now smokes too much for my likin... This ones not much to look at right now, need to clean it up...but I actually got reciepts on this one being built and drove it before pulling so I know this one is good :)

    [​IMG]
     
  8. joel63cj5

    joel63cj5 loose change

    With one rock poking in your back.
    monkeys
     
  9. neptco19

    neptco19 That guy....

    Got some new gauges installed...need to find the right ohm fuel gauge to replace the one stock gauge left

    [​IMG]

    Engine no. 4 installed...I even cleaned and painted up all ugly like :)

    [​IMG]
     
  10. neptco19

    neptco19 That guy....

    Replaced the bent tie rod

    [​IMG]

    Some new seat covers to protect it while its stored outside

    [​IMG]
     
    Last edited: Jan 11, 2009
  11. neptco19

    neptco19 That guy....

    [youtube]<object width="445" height="364"><param name="movie" value="http://www.youtube.com/v/RRCbybZmxvs&hl=en&fs=1&color1=0x5d1719&color2=0xcd311b&border=1"></param><param name="allowFullScreen" value="true"></param><param name="allowscriptaccess" value="always"></param><embed src="http://www.youtube.com/v/RRCbybZmxvs&hl=en&fs=1&color1=0x5d1719&color2=0xcd311b&border=1" type="application/x-shockwave-flash" allowscriptaccess="always" allowfullscreen="true" width="445" height="364"></embed></object>[/youtube]
     
  12. jayhawkclint

    jayhawkclint ΜΟΛΩΝ ΛΑΒΕ

    Man, here's to better luck with the latest transplant. :beer:
    Posted via Mobile Device
     
  13. cj5 buggy

    cj5 buggy Member

    looking and sounding great
     
  14. neptco19

    neptco19 That guy....

    Got some more stuff done today...

    grab bar on the pass side

    [​IMG]

    [​IMG]

    Old Tailgate

    [​IMG]

    New Tailgate

    [​IMG]

    Cage Tie In

    [​IMG]
     
  15. DanStew

    DanStew Preowned Merkin salesman Staff Member

    You know Jason, i think you need to buy that m170 frame on the GA forum. Then stretch your rig. It is time to supersize goldie.
     
  16. neptco19

    neptco19 That guy....

    lalalalalalala I cant hear you....I dont need any more "big" projects for a while. :beer:
     
  17. DanStew

    DanStew Preowned Merkin salesman Staff Member

    You know it has been on there for a while and he is itching to get rid of it :) Its on a frame with axles. ;) :)
     
  18. cj5 buggy

    cj5 buggy Member

    nice Jason...
     
  19. bkd

    bkd Moderator Supreme Staff Member 2022 Sponsor

    great looking welds on that grab bar, ....I need to do tie ins on my cage as well...looks great :beer:
    Jim S.
     
  20. neptco19

    neptco19 That guy....

    Made a little rack in the back behind the radiator to keep a cooler and toolbox on. Just need to find a piece of expanded and bolt it on then paint it all. The battery is mounted underneath it with a little room for another small box. Just ignore my fancy overflow bottle :D

    [​IMG]