• Registration trouble? Please use the "Contact Us" link at the bottom right corner of the page and your issue will be resolved.
Jon B.

Jon B.

2025 Sponsor 2026 Sponsor
Retired three times; still working. From SW Minnesota
Joined
Last seen
Messages
691
Media
3
Reaction score
3,728
Points
93

Latest activity Postings Media Albums About

    • Jon B.
      Jon B. reacted to ITLKSEZ's post in the thread Varg In Jeep's Clothing with Like Like.
      One mod I’ve wanted to make to this jeep from back when it was still a scribble on a notepad was to be able to weld from it. A Premier...
    • Jon B.
      Jon B. replied to the thread Willys Wagon.
      Holy Moly, Rocky! Eight of the rivets came out OK. I cut an ‘X’ in the head with a cutoff wheel, chiseled the heads off, then punched...
      • IMG_4530.jpeg
    • Jon B.
      Jon B. replied to the thread Willys Wagon.
      Way back, when the Ford engine was installed, the front crossmember got hacked up to make room for the fan. I’ve decided to remove it...
      • IMG_4529.jpeg
      • IMG_4528.jpeg
    • Jon B.
      Jon B. replied to the thread Willys Wagon.
      Yes, the drag link will connect to the hole in the tie rod end. The outer hole is too far from the ball joint pivot - the pitman arm is...
    • Jon B.
      Jon B. replied to the thread Willys Wagon.
      The front axle is pretty much done. I bought a set of one/ton tie rod & drag link ends from Barnes, then some steel tube from the local...
      • IMG_4523.jpeg
      • IMG_4524.jpeg
    • Jon B.
      Jon B. replied to the thread Rarely used tools.
      The “Christmas Tree” bit. I have two and use them frequently. They’re really nice for firewall pass-through holes. Jon B.
    • Jon B.
      Jon B. posted the thread Rarely used tools in The Tool Shed.
      When I added a power steering box to the FrankenJeep, I had to ream the hole in the pitman arm to fit the drag link end. I asked...
    • Jon B.
      Jon B. replied to the thread What Did You Do To Your Jeep Today?.
      I added a few ‘mods’ to the Jeep: Front recovery hooks A hand throttle Extended differential vents to stay above water Jon B.
      • IMG_4517.jpeg
      • IMG_4515.jpeg
      • IMG_4516.jpeg
      • IMG_4518.jpeg
      • IMG_4519.jpeg
    • Jon B.
      Jon B. reacted to Joe Adams's post in the thread 40 Years Later - The Re-build with Like Like.
      Still looking for a deal on an 8274 so this Honda will have to ride on the bumper for the time being.
    • Jon B.
      Jon B. reacted to timsresort's post in the thread Woodstock with Like Like.
      Back to the transfer case. This needs to get resolved. So, since I have Tera 3.15 gears, and an overdrive, I do not have an output gear...
    • Jon B.
      Jon B. replied to the thread 1970 CJ5 - CO.
      This is on the same page: https://m.facebook.com/marketplace/item/1760052151632961/ If I didn’t have a wagon project using up all of...
    • Jon B.
      Jon B. reacted to Fireball's post in the thread 1963 Us Navy Dj-3a with Like Like.
      It's been a busy weekend. The buddy that's joining me on the trip came down over the weekend so we could dry run stuff. This is...
    • Jon B.
      Jon B. replied to the thread For Sale T-90, D18, Warn OD in MN.
      SW; about 100 miles NE of Sioux Falls, SD. Eastern Yellow Medicine County, near Echo, MN. Jon B.
    • Jon B.
      Jon B. replied to the thread For Sale T-90, D18, Warn OD in MN.
      Yup; Ford (old) small bell adapter. The bell it attached to is a 5-bolt for the old (1950s to early 1960s) small V-8s. It’s welded...
    • Jon B.
      Jon B. posted the thread For Sale T-90, D18, Warn OD in MN in Early CJ-5 and CJ-6 Classifieds.
      As removed from my ‘53 Willys Station Wagon. Yes, I’d prefer to keep them together. Yes, I already have someone wanting just the OD...
      • IMG_4485.jpeg
    Show older items
  • Loading…
  • Loading…
  • Loading…
  • Loading…
Back
Top Bottom