1. Registration trouble? Please use the "Contact Us" link at the bottom right corner of the page and your issue will be resolved.
    Dismiss Notice

Roxor - Swing Pedal Assembly

Discussion in 'Roxor Tech' started by Jrobz23, Aug 31, 2018.

  1. Aug 31, 2018
    Jrobz23

    Jrobz23 Member

    Northern, WI
    Joined:
    Oct 3, 2016
    Messages:
    563
    Last edited: Aug 31, 2018
  2. Aug 31, 2018
    tarry99

    tarry99 Member Sponsor

    Northern California
    Joined:
    Oct 29, 2012
    Messages:
    3,770
    What is the measurement from the pedal foot pads to the pivot point above?
     
  3. Aug 31, 2018
    Sierra Bum

    Sierra Bum Member

    The High Sierra
    Joined:
    Oct 23, 2017
    Messages:
    145
    This looks a great possible option. I'm looking to install a swing petal set up in my 68' this winter. I'm assuming this is for a hydraulic clutch, and can be used with disc brakes? Any pics, measurements and info (like where to purchase the parts) would be appreciated. Thanks!
     
  4. Aug 31, 2018
    Jrobz23

    Jrobz23 Member

    Northern, WI
    Joined:
    Oct 3, 2016
    Messages:
    563
    14”
     
  5. Aug 31, 2018
    Jrobz23

    Jrobz23 Member

    Northern, WI
    Joined:
    Oct 3, 2016
    Messages:
    563
    Correct, hydro clutch, and front disc, rear drum. Parts can be had from a dealer. The Roxor site has a dealer finder page.

    Pics (including a shameless plug of the windshield and grill swap):

    Imgur
     
  6. Aug 31, 2018
    Sierra Bum

    Sierra Bum Member

    The High Sierra
    Joined:
    Oct 23, 2017
    Messages:
    145
    So I found the parts in the catalogue. For the petal assembly, clutch cylinder assembly, and brake cylinder assembly (including the little compact booster) it comes to $224. That's pretty darn good for new parts. I think Mahindra makes a pretty decent tractor so I bet the quality is there....

    The big question is.... can I get this to work with my existing clutch fork? With the Novak slave kit I've been looking at, I have to drop the tranny in order put Novak clutch fork in there.
     
  7. Sep 1, 2018
    Jrobz23

    Jrobz23 Member

    Northern, WI
    Joined:
    Oct 3, 2016
    Messages:
    563
    What motor/trans do you run?
     
  8. Sep 2, 2018
    Sierra Bum

    Sierra Bum Member

    The High Sierra
    Joined:
    Oct 23, 2017
    Messages:
    145
    225 oddfire v6 and an SM420. I l'd love to not have to drop my tranny. Although if I did it would be hard to resist putting Terra Low gears in my t-case. That would put me around 100:1.
     
  9. Sep 9, 2018
    Dgroshek

    Dgroshek Member

    TX
    Joined:
    Dec 11, 2017
    Messages:
    191
    I'd like to get some measurements. Thinking about this for a swinging pedal swap in my cj5. What's the distance between pedals? What is the overall width of the mounting bracket? Thanks!
     
  10. Sep 9, 2018
    zinertia2

    zinertia2 "and which part are you keeping?"

    San Diego
    Joined:
    Feb 15, 2018
    Messages:
    58
    Just ordered a set. Now waiting for delivery ( no lead time available from the distributor)
    Dennis
     
  11. Sep 9, 2018
    jeepstar

    jeepstar Sponsor Sponsor

    Sheboygan
    Joined:
    Jun 28, 2006
    Messages:
    1,289
    Cool. Im curious
     
  12. Sep 10, 2018
    Dgroshek

    Dgroshek Member

    TX
    Joined:
    Dec 11, 2017
    Messages:
    191
    Ended up ordering a set too. Hopefully these work. Was planning on using wilwood swinging pedals but I just can't figure how to get the brake pedal to fit between the steering column and the engine clearance hump on the firewall
     
  13. Sep 10, 2018
    RVSwisher

    RVSwisher Member

    Rochester, MN
    Joined:
    Jul 11, 2006
    Messages:
    99
    Where are you purchasing parts from? Do you have a link to the parts view and ordering instructions?

    Thanks

    RVS
     
  14. Sep 10, 2018
    Dgroshek

    Dgroshek Member

    TX
    Joined:
    Dec 11, 2017
    Messages:
    191
    Go here: ROXOR Offroad then find the part; if looking for the pedal assembly, it's Item #0802BAA10150N

    You will then have to enter your zip code and find the nearest distributor. Call them up and order from them. I spoke with Roxor and they do not sell direct from them.
     
  15. Sep 11, 2018
    Keys5a

    Keys5a Sponsor Sponsor

    Joined:
    Jan 23, 2014
    Messages:
    2,139
    Maybe because I didn't sign in to the Roxor page, but most of the parts I went searching, prices say to "call your dealer". The front fenders are of particular interest. I might stop by the local dealer again to check out the seats in person. They are priced at $68.99 each- a bargain!
    -Donny
     
  16. Sep 11, 2018
    jeepstar

    jeepstar Sponsor Sponsor

    Sheboygan
    Joined:
    Jun 28, 2006
    Messages:
    1,289
    compared to the 300 bucks for smittybuilt, id buy them all day at that price!!
     
  17. Sep 11, 2018
    tarry99

    tarry99 Member Sponsor

    Northern California
    Joined:
    Oct 29, 2012
    Messages:
    3,770
    Whoever gets one of those pedal assembles first............post some pictures and measurements.
     
    Danefraz likes this.
  18. Sep 12, 2018
    Jrobz23

    Jrobz23 Member

    Northern, WI
    Joined:
    Oct 3, 2016
    Messages:
    563
    Sorry been travelling. You guys still need any pedal assembly measurements?
     
  19. Sep 12, 2018
    zinertia2

    zinertia2 "and which part are you keeping?"

    San Diego
    Joined:
    Feb 15, 2018
    Messages:
    58
    Can you measure
    1. Firewall to dash (length of pedal assembly)
    2. Total pedal length (pivot to center of foot pad)
    3. Pedal pivot to brake pushrod distance ( will give me pedal ratio between 2 & 3)
    4. Width of pedal assembly

    Greatly appreciate this!
    Dennis
     
  20. Sep 13, 2018
    Dgroshek

    Dgroshek Member

    TX
    Joined:
    Dec 11, 2017
    Messages:
    191
    The above will help me as well though I did go ahead and place an order for these anyway
     

Share This Page

New Posts