1. Registration trouble? Please use the "Contact Us" link at the bottom right corner of the page and your issue will be resolved.
    Dismiss Notice

Need Ideas For A Seat Bracket...

Discussion in 'Builds and Fabricators Forum' started by txtoller, Mar 7, 2019.

  1. Mar 7, 2019
    txtoller

    txtoller Member 2023 Sponsor 2022 Sponsor

    Weatherford, TX
    Joined:
    May 28, 2014
    Messages:
    976
    My passenger seat bracket is fubar and I need ideas for an easy and efficient mount.

    Thanks!
     
    txtoller, Mar 7, 2019
    #1
  2. Mar 7, 2019
    Jw60

    Jw60 Cool school 2024 Sponsor 2023 Sponsor 2022 Sponsor

    Sedalia MO.
    Joined:
    Apr 8, 2008
    Messages:
    4,778
    I don't have a tool box so I copied the driver side and added a slotted bracket (drilled and cut nut) to mimic the original for the seat to pivot on.
     
    Jw60, Mar 7, 2019
    #2
    cj3may likes this.
  3. Mar 8, 2019
    txtoller

    txtoller Member 2023 Sponsor 2022 Sponsor

    Weatherford, TX
    Joined:
    May 28, 2014
    Messages:
    976
    I will add that I still have the tool box. I have seen some, but haven't been able to locate them again.
     
    txtoller, Mar 8, 2019
    #3
  4. Mar 8, 2019
    Buildflycrash

    Buildflycrash More or Less in Line. 2024 Sponsor 2022 Sponsor

    Gulf Breeze FL...
    Joined:
    Jun 5, 2007
    Messages:
    3,592
    Good luck. Passenger seat bracket was one of the hardest items to source for my build. I have not seen a good homemade that kept the toolbox in play.
     
    Buildflycrash, Mar 8, 2019
    #4
  5. Mar 8, 2019
    FinoCJ

    FinoCJ 1970 CJ5 Staff Member

    Bozeman, MT
    Joined:
    Jul 18, 2013
    Messages:
    5,620
    I think you could make a pretty good one from some 1" square tubing. Make the two halves and weld on two tabs to bolt them together and keep the flip forward capability for toolbox access. There are some OEM ones available here in Colo - not sure its worth it to you to get them to TX. Here would be some contacts around here that most likely have it....
    Jeeps Unlimited: Jeep Parts - Huge Shipment of New Parts and SALE
    These guys (Schlepy brothers) have quite a lot of stuff - one is in Bellvue and one is in Laporte - very close together. I found some gas tank hangers and my early driver side seat bracket from these guys :
    CJ5 and CJ7 & Willys Jeep parts
    Lots of Jeep Parts
     
    FinoCJ, Mar 8, 2019
    #5
  6. Mar 8, 2019
    Norcal69

    Norcal69 Out of the box thinker 2024 Sponsor 2023 Sponsor 2022 Sponsor

    Northern California
    Joined:
    Sep 6, 2014
    Messages:
    3,561
    Post #34 on page 2 of my build thread shows what I did. My seats have a built in forward tilt feature. I hinged the rear of the seat and have hitch pins on the front.

     
    Norcal69, Mar 8, 2019
    #6
  7. Mar 8, 2019
    txtoller

    txtoller Member 2023 Sponsor 2022 Sponsor

    Weatherford, TX
    Joined:
    May 28, 2014
    Messages:
    976
    I found your photos, I think I may try and go that route, do you have any photos of the rear of the seat?
     
    txtoller, Mar 8, 2019
    #7
  8. Mar 8, 2019
    Norcal69

    Norcal69 Out of the box thinker 2024 Sponsor 2023 Sponsor 2022 Sponsor

    Northern California
    Joined:
    Sep 6, 2014
    Messages:
    3,561

    [​IMG]

    [​IMG]

    [​IMG]
     
    Norcal69, Mar 8, 2019
    #8
  9. Mar 8, 2019
    txtoller

    txtoller Member 2023 Sponsor 2022 Sponsor

    Weatherford, TX
    Joined:
    May 28, 2014
    Messages:
    976
    Thank you!
     
    txtoller, Mar 8, 2019
    #9
New Posts