1. Registration trouble? Please use the "Contact Us" link at the bottom right corner of the page and your issue will be resolved.
    Dismiss Notice

F134 Oil Pressure Issues Again

Discussion in 'Early CJ5 and CJ6 Tech' started by 1957Willys, Aug 26, 2017.

  1. Aug 26, 2017
    1957Willys

    1957Willys Member

    Birmingham, Alabama
    Joined:
    Mar 23, 2012
    Messages:
    698
    I went for a drive today and the oil pressure stayed around 20-25psi at 45mph and 5psi at idle. When I press on the accelerator pedal the oil pressure slowly rises. I think the oil pump is failing or the oil pump puckup tube is cracked.
     
  2. Aug 26, 2017
    Glenn

    Glenn Kinda grumpy old man Staff Member

    Apopka, Fl
    Joined:
    Sep 21, 2002
    Messages:
    12,367
    I don't remember what problems you had before. Same symptoms? Did it get better? Have you checked the relief spring on the pump?
     
  3. Aug 26, 2017
    1957Willys

    1957Willys Member

    Birmingham, Alabama
    Joined:
    Mar 23, 2012
    Messages:
    698
    I shimmed the spring in the pump with #10 washers. And it has been good since. The oil pressure before was 10psi at idle and 50-55psi while driving.
     
  4. Aug 27, 2017
    Glenn

    Glenn Kinda grumpy old man Staff Member

    Apopka, Fl
    Joined:
    Sep 21, 2002
    Messages:
    12,367
    I would start by checking the spring again, make sure it didn't break. Oil pump shouldn't all of the sudden go bad, it would be very gradual generally. Obviously you've made sure it has enough oil so I won't ask. Is the oil pickup possibly becoming clogged? What kind of line do you have going to the pressure gauge?
     
  5. Aug 27, 2017
    1957Willys

    1957Willys Member

    Birmingham, Alabama
    Joined:
    Mar 23, 2012
    Messages:
    698
    It's a 1/4 inch line going to the gauge and the gauge is a AC gauge. I have never had the pan off I might start there and see what I can find.
     
  6. Aug 27, 2017
    Daryl

    Daryl Sponsor

    Bonney Lake, WA
    Joined:
    May 25, 2006
    Messages:
    2,871
    I would strain your motor oil through a white t shirt to look for metal. If you lost oil pressure once, and then got it back by tweaking the pump and it is now going lower you may have an issue causing wear.
     
  7. Aug 27, 2017
    1957Willys

    1957Willys Member

    Birmingham, Alabama
    Joined:
    Mar 23, 2012
    Messages:
    698
    Well I pulled the pan off today and found the oil pump pickup screen to full of some type of gasket material. Next I'm going to pull the pump and take it apart.
     
    Last edited: Aug 27, 2017
  8. Aug 27, 2017
    1957Willys

    1957Willys Member

    Birmingham, Alabama
    Joined:
    Mar 23, 2012
    Messages:
    698
  9. Aug 27, 2017
    Glenn

    Glenn Kinda grumpy old man Staff Member

    Apopka, Fl
    Joined:
    Sep 21, 2002
    Messages:
    12,367
    Well, I imagine cleaning that should solve the problem.
     
  10. Aug 27, 2017
    1957Willys

    1957Willys Member

    Birmingham, Alabama
    Joined:
    Mar 23, 2012
    Messages:
    698
    I hope it does I found a reman oil pump that is still new in the box from the 50's or 60's i'm going to install it and clean the pan the pickup tube. Then I'll see what happens if it's still low on pressure then I'll know its internal wear on the bearings. I have a rebuilt F134 sitting in the garage waiting so all hope is not lost.
     
  11. Aug 28, 2017
    1960willyscj5

    1960willyscj5 Well-Known Member

    Mesa, Arizona
    Joined:
    Nov 27, 2006
    Messages:
    2,793
    Umm, where did the gasket material come from?
     
  12. Aug 28, 2017
    Howard Eisenhauer

    Howard Eisenhauer Administrator Staff Member

    Tantallon, Nova...
    Joined:
    Nov 22, 2003
    Messages:
    8,102
    I actually dropped the pan & pumped oil under pressure into the gallery through the oil sender port to see where it comes out at- 90% if not more comes through the timing gear oiler & oil filter return.

    The crank & rod bearings, at least fresh ones, "weep".

    The camshaft ones "dribble".



    If you try this at home wear goggles.


    Don't ask how I know.


    H.
     
    1957Willys and Glenn like this.
  13. Aug 28, 2017
    1957Willys

    1957Willys Member

    Birmingham, Alabama
    Joined:
    Mar 23, 2012
    Messages:
    698

    How were you able to pump oil into the oil galley? What type of pump did you use manual or electric?
     
  14. Aug 28, 2017
    Howard Eisenhauer

    Howard Eisenhauer Administrator Staff Member

    Tantallon, Nova...
    Joined:
    Nov 22, 2003
    Messages:
    8,102
    I built a vessel out of PVC (80 PSI rated) pipe, about a foot long, with a shraeder valve on one end & a valve & whip end on the other. Filled to about 3/4 with oil, pressurized it to about 40 PSI screwed the whip end into the sender port & opened the valve- got about 10 seconds of flow on each shot.

    H.

    p.s.- except for a head shaped outline it makes a mess on the floor.

    p.p.s.- of course while you have the pan off you might as well plastigauge the bearings anyhow :whistle:
     
  15. Aug 28, 2017
    1957Willys

    1957Willys Member

    Birmingham, Alabama
    Joined:
    Mar 23, 2012
    Messages:
    698
    So I was looking at oil pumps for a F134 and found there are two different type housings aluminum and cast iron. Are there any big differences between them internally?
     
  16. Aug 28, 2017
    1960willyscj5

    1960willyscj5 Well-Known Member

    Mesa, Arizona
    Joined:
    Nov 27, 2006
    Messages:
    2,793
    The oil pump for the F-Head 134 engine will also fit the L-Head 134 that uses meshing timing gears. You need a different oil pump for the L-Head 134 engine that uses a timing chain instead of meshing gears.
     
  17. Aug 30, 2017
    1957Willys

    1957Willys Member

    Birmingham, Alabama
    Joined:
    Mar 23, 2012
    Messages:
    698
    That's a good question when I cleaned the pan at work I noticed the old gasket had been glued on with yellow weather strip adhesive. So maybe it was replaced at some point in time. I'm going to try and reinstall the pan tomorrow I hope all the junk in the screen was the problem.
     
  18. Aug 30, 2017
    Glenn

    Glenn Kinda grumpy old man Staff Member

    Apopka, Fl
    Joined:
    Sep 21, 2002
    Messages:
    12,367
    The symptoms sure point to that.
     
  19. Aug 31, 2017
    1957Willys

    1957Willys Member

    Birmingham, Alabama
    Joined:
    Mar 23, 2012
    Messages:
    698
    Ok the new pump came in today and one thing I noticed is it does not have a oil port on the side of the housing for the shaft. Will that affect anything? I did a search and found that some pumps have been seizing up?
     
  20. Aug 31, 2017
    Glenn

    Glenn Kinda grumpy old man Staff Member

    Apopka, Fl
    Joined:
    Sep 21, 2002
    Messages:
    12,367
    I don't know about the oil port , but where did you get the pump from?
     
New Posts