1. Registration trouble? Please use the "Contact Us" link at the bottom right corner of the page and your issue will be resolved.
    Dismiss Notice

F134 Carb Linkage

Discussion in 'Early CJ5 and CJ6 Tech' started by Mike Allen, Jan 14, 2018.

  1. Jan 14, 2018
    Mike Allen

    Mike Allen New Member

    Louisville, KY
    Joined:
    Dec 26, 2017
    Messages:
    22
    Tried to search forum to no avail. Could a member post a pic of the gas pedal linkage from firewall to the bell crank on the value adjustment cover stud. (engine compartment) I am good on all the rest of the linkage. PO used torch to disconnect gas pedal linkage. Fabricating the missing end (Threaded I would think) should not be too hard for me. A pic would tell me if I am thinking right. Again--F134 engine.

    Thanks--Mike
     
    Mike Allen, Jan 14, 2018
    #1
  2. Jan 14, 2018
    Glenn

    Glenn Kinda grumpy old man Staff Member

    Apopka, Fl
    Joined:
    Sep 21, 2002
    Messages:
    12,375
    It could be tricky to try to replicate the bends but it is just a piece of rod that goes from the gas pedal to the bell crank you mentioned. It might be worth just buying one if you can. Not saying it's super difficult of course. I'll try to get a pic tomorrow unless someone beats me to it.
     
    Glenn, Jan 14, 2018
    #2
  3. Jan 14, 2018
    Focker

    Focker That's a terrible idea...What time? Staff Member

    WA
    Joined:
    Aug 18, 2014
    Messages:
    7,540
    Focker, Jan 14, 2018
    #3
    Glenn likes this.
  4. Jan 14, 2018
    Mike Allen

    Mike Allen New Member

    Louisville, KY
    Joined:
    Dec 26, 2017
    Messages:
    22
    This forum is number one! I am clear on how it should look due to the replies. Most of the rod was there. I just welded a 4" section of 1/4" round rod and threaded the end. I was not sure if the rod ran on the engine side or the fender side of the bell crank. If that makes sense? Once again--Your help is greatly needed and appreciated.
    Mike
     
    Mike Allen, Jan 14, 2018
    #4
  5. Jan 15, 2018
    PeteL

    PeteL If it wasn't for physics, and law enforcement... 2024 Sponsor 2023 Sponsor 2022 Sponsor

    Hills of NH
    Joined:
    Aug 3, 2003
    Messages:
    9,806
    I find this kind of thing is easy to locate with a ten second "image search" on Bing, or whatever.

    Fuel Accelerator.jpg
     
    PeteL, Jan 15, 2018
    #5
  6. Jan 15, 2018
    Mike Allen

    Mike Allen New Member

    Louisville, KY
    Joined:
    Dec 26, 2017
    Messages:
    22
    PeteL--Thank you for the 10 seconds of your time. This diagram is perfect and actually it shows the rod on the fender side
    of the bell crank. I guess either side works fine as long as it doesn't bind.

    I am not a computer person. Thankfully there are forums of like minded people that enjoy sharing ideas and knowledge.
    Thank you for your help PeteL
     
    Mike Allen, Jan 15, 2018
    #6
  7. Jan 15, 2018
    PeteL

    PeteL If it wasn't for physics, and law enforcement... 2024 Sponsor 2023 Sponsor 2022 Sponsor

    Hills of NH
    Joined:
    Aug 3, 2003
    Messages:
    9,806
    Me either. Glad to know I'm not the only one.
    :beer:
     
    PeteL, Jan 15, 2018
    #7
New Posts