1. Registration trouble? Please use the "Contact Us" link at the bottom right corner of the page and your issue will be resolved.
    Dismiss Notice

Search Results

Search Again
Page 1 of 2
  1. 90 degree
    Post

    Howell Odd Fire V6 Fuel Injection Kit Install

    hope the crank sensor is coming along
    Post by: 90 degree, Mar 28, 2021 in forum: Early CJ5 and CJ6 Tech
  2. 90 degree
    Post

    Howell Odd Fire V6 Fuel Injection Kit Install

    hey jw i was looking a some of your old pictures. my heater hoses are connected to the right rear of the intake manifold, and the the port on the...
    Post by: 90 degree, Mar 28, 2021 in forum: Early CJ5 and CJ6 Tech
  3. 90 degree
    Post

    Howell Odd Fire V6 Fuel Injection Kit Install

    I was explaning to jw about the coolant sensor. to me it is about the most important part of that tbi system. I was supposed to try to find a...
    Post by: 90 degree, Mar 16, 2021 in forum: Early CJ5 and CJ6 Tech
  4. 90 degree
    Post

    My First Jeep Build 69 Cj-5

    this is something you might like. i have a hardtop and had the same mirrors, but didn't like that the door would hit them and they stuck out a...
    Post by: 90 degree, Jan 24, 2021 in forum: Builds and Fabricators Forum
  5. 90 degree
    Post

    Engine Cuts Out

    i think the formula is if it is backfiring out of the carb it is firing too soon . needs to be retarted. make it fire later. if it backfires out...
    Post by: 90 degree, Jan 17, 2021 in forum: Intermediate CJ-5/6/7/8
  6. 90 degree
    Post

    Howell Odd Fire V6 Fuel Injection Kit Install

    hi me again, that coolant sensor must be in the hose going to the heater yes. you probably see after using this kit for a while that when you...
    Post by: 90 degree, Dec 23, 2020 in forum: Early CJ5 and CJ6 Tech
  7. 90 degree
    Post

    Howell Odd Fire V6 Fuel Injection Kit Install

    oh geeze me again, i was looking at one of you pictures, the hose that your coolant sensor is in, it disappears into the fire wall. is it a heater...
    Post by: 90 degree, Dec 22, 2020 in forum: Early CJ5 and CJ6 Tech
  8. 90 degree
    Post

    Howell Odd Fire V6 Fuel Injection Kit Install

    did the kit come with the crank sensor and coolant temperature sensor, map sensor too.. might not be too hard to hang the crank sensor. maybey...
    Post by: 90 degree, Dec 22, 2020 in forum: Early CJ5 and CJ6 Tech
  9. 90 degree
    Post

    Howell Odd Fire V6 Fuel Injection Kit Install

    this kit must have a coolant temp sensor. that i think runs the engine when it starts and is cold. as the engine warms up the o2 sensors take...
    Post by: 90 degree, Oct 7, 2020 in forum: Early CJ5 and CJ6 Tech
  10. 90 degree
    Post

    Buick V6 Thread Fix (exhaust)

    get some measurement so you can redrill in the same place. get a mig welder and fill it with cast iron wire. cast usually drills pretty good.
    Post by: 90 degree, Oct 3, 2020 in forum: Early CJ5 and CJ6 Tech
  11. 90 degree
    Post

    Howell Odd Fire V6 Fuel Injection Kit Install

    with the picture at the top, of the tbi, i swear it looks like the throttle body off of a 4.3 chevy engine
    Post by: 90 degree, Sep 27, 2020 in forum: Early CJ5 and CJ6 Tech
  12. 90 degree
    Post

    From Bad To Worse With Broken Bolt!! Don't Do What I Did.

    the bearing should still pull ok. might be a little harder if you burred up the bottom. if it goes too hard you could weaken the bearing by...
    Post by: 90 degree, Aug 11, 2020 in forum: Early CJ5 and CJ6 Tech
  13. 90 degree
    Post

    From Bad To Worse With Broken Bolt!! Don't Do What I Did.

    how far down in this hole is the broken piece. carbide bits are usually pretty short so are burrs. they make some drill tools that cut and extract...
    Post by: 90 degree, Aug 1, 2020 in forum: Early CJ5 and CJ6 Tech
  14. 90 degree
    Post

    My First Jeep Build 69 Cj-5

    again very very nice. good choice on the box
    Post by: 90 degree, Jul 31, 2020 in forum: Builds and Fabricators Forum
  15. 90 degree
    Post

    From Bad To Worse With Broken Bolt!! Don't Do What I Did.

    you will need a piece of 1/2 in or 3/8 threaded rod. a couple of nuts. we will build a cheap sliding hammer.the washer might be a 7/8 or...
    Post by: 90 degree, Jul 28, 2020 in forum: Early CJ5 and CJ6 Tech
  16. 90 degree
    Post

    Where To Find Parts

    ill try that one
    Post by: 90 degree, Jul 28, 2020 in forum: Early CJ5 and CJ6 Tech
  17. 90 degree
    Post

    Where To Find Parts

    jw auto wreckers.com california
    Post by: 90 degree, Jul 28, 2020 in forum: Early CJ5 and CJ6 Tech
  18. 90 degree
    Post

    My First Jeep Build 69 Cj-5

    very very nice
    Post by: 90 degree, Jul 18, 2020 in forum: Builds and Fabricators Forum
  19. 90 degree
    Post

    Imported Gauges From Ebay

    this seems like a pretty old thread but maybey someone will see my post. who made the sppedometers for jeep for 1969 cj5's with the 0 to 9 face....
    Post by: 90 degree, Jun 14, 2020 in forum: Early CJ5 and CJ6 Tech
  20. 90 degree
    Post

    My First Jeep Build 69 Cj-5

    any info on this part mike, numbers where it came from thanks
    Post by: 90 degree, May 17, 2020 in forum: Builds and Fabricators Forum
Showing results 1 to 20 of 33 Next >
Search Again
Page 1 of 2
New Posts