1. Registration trouble? Please use the "Contact Us" link at the bottom right corner of the page and your issue will be resolved.
    Dismiss Notice

Search Results

Search Again
Page 1 of 7
  1. BobH
    Post

    55 Cj5 No Spark And Questions

    Amazon has them.
    Post by: BobH, May 8, 2023 in forum: Early CJ5 and CJ6 Tech
  2. BobH
    Post

    Crate Engines (sbc)

    What about an EcoBoost swap? They have good power in a smaller package. I have a 2016 F150 with a 3.5 and am very happy with it.
    Post by: BobH, Jul 7, 2020 in forum: Builds and Fabricators Forum
  3. BobH
    Post

    Re-jet Carburetor For High Altitude?

    We had prescription 800mg ibuprofen that was great!! Now I’m on blood thinners and can’t take it anymore.
    Post by: BobH, Jun 18, 2020 in forum: Early CJ5 and CJ6 Tech
  4. BobH
    Post

    Re-jet Carburetor For High Altitude?

    The plugs are black, haven’t done a compression test, but it runs fine.
    Post by: BobH, Jun 16, 2020 in forum: Early CJ5 and CJ6 Tech
  5. BobH
    Post

    Re-jet Carburetor For High Altitude?

    I did the opposite with my 60 CJ5 (F134), went from 9000 ft in Colorado to 35 ft in Fl. What jets should I be using?
    Post by: BobH, Jun 16, 2020 in forum: Early CJ5 and CJ6 Tech
  6. BobH
    Thread

    Pto Winch How To???

    I have a 60 CJ5 with a PTO run winch (not wench). It is a Konig winch with a lever and a pin. I need to know position the PTO, transfer case,...
    Thread by: BobH, Jan 13, 2020, 12 replies, in forum: Early CJ5 and CJ6 Tech
  7. BobH
    Post

    Symptoms Of A Crack In The Block Vs. Gasket Leak?

    I had the same thing happen to an old car that I only drove 10 min to work. I started driving it for an hour once a week and the problem went away.
    Post by: BobH, Jan 9, 2020 in forum: Intermediate CJ-5/6/7/8
  8. BobH
    Post

    Battery Charger Recommendation?

    I have 2 Battery Tenders. One I have used for years with no trouble.
    Post by: BobH, Jan 3, 2020 in forum: The Tool Shed
  9. BobH
    Post

    Was A Colorado, Now A Florida Jeep

    Never mind. My NEW HF test light doesn’t work. I used my multi meter and I have voltage. :banghead::bananatool:
    Post by: BobH, Jan 2, 2020 in forum: Builds and Fabricators Forum
  10. BobH
    Post

    Was A Colorado, Now A Florida Jeep

    Finally was able to look at the ignition switch and I can’t find any power to it. The BATT post has nothing. I assume that should be always hot. I...
    Post by: BobH, Jan 2, 2020 in forum: Builds and Fabricators Forum
  11. BobH
    Post

    Was A Colorado, Now A Florida Jeep

    I just tried it again. First try, nothing. I jiggled the key, and it cranked. :steamed::steamed::steamed: This is why I replaced the first time.
    Post by: BobH, Dec 23, 2019 in forum: Builds and Fabricators Forum
  12. BobH
    Post

    Was A Colorado, Now A Florida Jeep

    Battery is good. I keep it on a battery tender and at last check it had 12+ volts out of it.
    Post by: BobH, Dec 23, 2019 in forum: Builds and Fabricators Forum
  13. BobH
    Post

    Was A Colorado, Now A Florida Jeep

    Last night I went out to start the Jeep. I cranked it about 5-10 seconds and it didn’t start. I tried again and it turned over once, and it was...
    Post by: BobH, Dec 23, 2019 in forum: Builds and Fabricators Forum
  14. BobH
    Post

    Was A Colorado, Now A Florida Jeep

    Thanks Jeepstar.
    Post by: BobH, Dec 22, 2019 in forum: Builds and Fabricators Forum
  15. BobH
    Post

    Was A Colorado, Now A Florida Jeep

    Haven’t posted much here, but have been a little busy. I changed all the fluids, messed with the tail lights to get them working, and other stuff...
    Post by: BobH, Dec 20, 2019 in forum: Builds and Fabricators Forum
  16. BobH
    Post

    Varg In Jeep's Clothing

    :rofl:Me to. Thought it is just the way it is.
    Post by: BobH, Dec 11, 2019 in forum: Builds and Fabricators Forum
  17. BobH
    Post

    Multiple Pass Welding Question...

    Thank you sir. That sets the importance of duty cycle. Is there any way of knowing when you have reached it other than of watching the time?
    Post by: BobH, Dec 2, 2019 in forum: The Tool Shed
  18. BobH
    Post

    Multiple Pass Welding Question...

    For those of who have never welded (but want to) can someone explain duty cycle and how to know when you have reached it and the importance of it.
    Post by: BobH, Dec 2, 2019 in forum: The Tool Shed
  19. BobH
    Post

    Was A Colorado, Now A Florida Jeep

    They changed the brake cylinders to feed at 90 deg (straight up) but didn’t change the part number. The NAPA guy hooked me up with some 45 deg...
    Post by: BobH, Nov 20, 2019 in forum: Builds and Fabricators Forum
  20. BobH
    Post

    Was A Colorado, Now A Florida Jeep

    Got the seats mounted and now my head hits the soft top and I’m looking straight at the top windshield frame. All the lights work except the brake...
    Post by: BobH, Nov 20, 2019 in forum: Builds and Fabricators Forum
Showing results 1 to 20 of 129 Next >
Search Again
Page 1 of 7
New Posts