1. Registration trouble? Please use the "Contact Us" link at the bottom right corner of the page and your issue will be resolved.
    Dismiss Notice

Search Results

Search Again
Page 1 of 4
  1. jeepaholic
    Post

    Wasting time....woody

    http://up.craigslist.org/cto/1389520910.html
    Post by: jeepaholic, Oct 23, 2009 in forum: Builds and Fabricators Forum
  2. jeepaholic
    Post

    British Columbia do it all CJ2A build with V8 Power

    I have 19 spline shafts and spider gears for a open carrier if you want to upgrade now? Following along as this is sort of how I want mine.
    Post by: jeepaholic, Nov 25, 2008 in forum: Builds and Fabricators Forum
  3. jeepaholic
    Post

    73' CJ5 with 4BT, D44F, D44R Project

    The sm465,T18/19, th400 were all behind a 4bt. A nv4500 is pretty using 6bt parts though. I would find a T18 since it is pretty much the same a a...
    Post by: jeepaholic, Oct 18, 2008 in forum: Builds and Fabricators Forum
  4. jeepaholic
    Post

    2.3l ford motor swap

    Not really started it yet. Still working on the frame and body. I found this when I was searching for some 5.0 HO wiring stuff...
    Post by: jeepaholic, Sep 29, 2008 in forum: Flat Fender Tech
  5. jeepaholic
    Post

    The Gold Project

    wide track J-truck
    Post by: jeepaholic, Sep 29, 2008 in forum: Builds and Fabricators Forum
  6. jeepaholic
    Post

    where to get stock body mount rubbers

    Sorry, I thought they were thick rubber. Didn't mean to use them whole.
    Post by: jeepaholic, Sep 22, 2008 in forum: Early Jeep Restoration and Research
  7. jeepaholic
    Post

    where to get stock body mount rubbers

    hockey pucks
    Post by: jeepaholic, Sep 22, 2008 in forum: Early Jeep Restoration and Research
  8. jeepaholic
    Post

    225 w. offenhauser 360, mating issues? will not fit?

    Has the engine been rebuilt, the block or heads milled?
    Post by: jeepaholic, Sep 21, 2008 in forum: Early CJ5 and CJ6 Tech
  9. jeepaholic
    Post

    Axle shafts

    Where you at? I have a set for sale.
    Post by: jeepaholic, Sep 15, 2008 in forum: Early CJ5 and CJ6 Tech
  10. jeepaholic
    Post

    Driveable! 66 CJ-6A

    You don't need the $500 adapter for the T18, I just used a Jeep T18 (Scout 18/19 works also) factory adapter for the dana 20 and output shaft. You...
    Post by: jeepaholic, Sep 12, 2008 in forum: Builds and Fabricators Forum
  11. jeepaholic
    Post

    2.3l ford motor swap

    Yup the scout uses studs in front of the case. Hmmm, I know there are two different jeep inputs, I will have to check that. Thanks, for the input
    Post by: jeepaholic, Aug 29, 2008 in forum: Flat Fender Tech
  12. jeepaholic
    Post

    2.3l ford motor swap

    After some more research and using this great info I came up with a plan to pull this off. Using the pinto bell, a Scout T18 uses a smaller...
    Post by: jeepaholic, Aug 28, 2008 in forum: Flat Fender Tech
  13. jeepaholic
    Post

    The Gold Project

    So how did the dana 20 work with the offset rear? IIRC you put a dana 18 in? Just curious as I am thinking of running a dana 300 with a offset rear.
    Post by: jeepaholic, Jul 23, 2008 in forum: Builds and Fabricators Forum
  14. jeepaholic
    Post

    Frame choice?

    Both frames are in good shape as far as I can tell on the 2a Welding is not a problem Yes it is set up with a v6 (drive train is all still on...
    Post by: jeepaholic, Jun 15, 2008 in forum: Flat Fender Tech
  15. jeepaholic
    Thread

    Frame choice?

    Well just picked up a 47 cj2a and still have a buick 225 and sm465 I want to run. So 71 cj5 frame or original cj2a frame? I know the 5...
    Thread by: jeepaholic, Jun 15, 2008, 7 replies, in forum: Flat Fender Tech
  16. jeepaholic
    Post

    Mud Shovel

    Moving along, get her done so we can go wheeling :)
    Post by: jeepaholic, Apr 23, 2008 in forum: Builds and Fabricators Forum
  17. jeepaholic
    Post

    Wow Look at this 59 cj3b,Bill is good looking

    Got the rear springs and shocks installed. So the rear axle is all bolted back in. Hoping the input retainer shows up tomorrow so I can install...
    Post by: jeepaholic, Apr 22, 2008 in forum: Builds and Fabricators Forum
  18. jeepaholic
    Post

    Wow Look at this 59 cj3b,Bill is good looking

    Looks good :) I got the rear springs removed, drilled new holes in the rear axle perches to move the axle back 1" (help center it in the wheel...
    Post by: jeepaholic, Apr 21, 2008 in forum: Builds and Fabricators Forum
  19. jeepaholic
    Post

    Wow Look at this 59 cj3b,Bill is good looking

    NTWonline's special :) [IMG] [IMG] [IMG] [IMG] [IMG] I got the front springs under the front and mocked up my 44 but didn't get...
    Post by: jeepaholic, Apr 13, 2008 in forum: Builds and Fabricators Forum
  20. jeepaholic
    Post

    63' willys....dana 25 to dana 30 swap.

    All high pinion are driver side diff, so you will have to have it retubed. I have done a couple of 74-79 wagoneer dana 44 fronts that are...
    Post by: jeepaholic, Apr 13, 2008 in forum: Early CJ5 and CJ6 Tech
Showing results 1 to 20 of 79 Next >
Search Again
Page 1 of 4
New Posts