1. Registration trouble? Please use the "Contact Us" link at the bottom right corner of the page and your issue will be resolved.
    Dismiss Notice

Search Results

Search Again
Page 1 of 7
  1. endless expense 45
    Post

    Was there ever a fiberglass hard top for Ecj

    Well top is in perfect shape and the jeep won't bad either,It ended up being a 74 CJ-5 so it won't work on my 79 CJ-5. Heres a link, my buddy who...
    Post by: endless expense 45, Oct 14, 2010 in forum: Early CJ5 and CJ6 Tech
  2. endless expense 45
    Post

    Dana 300 Question

    The shaft from Advance Adapters worked perfect,The big brown truck dropped it off yesterday and I got it installed.
    Post by: endless expense 45, Mar 2, 2010 in forum: Intermediate CJ-5/6/7/8
  3. endless expense 45
    Post

    new clutch stuck

    I agree I have seen it 3 or 4 times,it is a common mistake.If the throwout fork is moving that the clutch disk almost has to be the problem!
    Post by: endless expense 45, Feb 23, 2010 in forum: Flat Fender Tech
  4. endless expense 45
    Post

    Dana 300 Question

    Thanks nickmil I called advance adapters and they sold me the spud shaft(the shaft in kit part # 50-6304) I needed to adapt the Turbo 350/ Dana...
    Post by: endless expense 45, Feb 22, 2010 in forum: Intermediate CJ-5/6/7/8
  5. endless expense 45
    Thread

    Dana 300 Question

    I have tried searching this but I just can't find the answer I am looking for.I am tring to find out what spud shaft I need to adapt a 23 spline...
    Thread by: endless expense 45, Feb 21, 2010, 4 replies, in forum: Intermediate CJ-5/6/7/8
  6. endless expense 45
    Post

    Need wiring help on an 81 CJ-7

    Thanks that is exactly what I was looking for!
    Post by: endless expense 45, Feb 10, 2010 in forum: Intermediate CJ-5/6/7/8
  7. endless expense 45
    Thread

    Need wiring help on an 81 CJ-7

    I am tring to find a complete wiring diagram for a 1981 CJ-7 Laredo.I am attempting to replace teh AMC 360 with a Fuel injected chevy 350,I have...
    Thread by: endless expense 45, Feb 9, 2010, 3 replies, in forum: Intermediate CJ-5/6/7/8
  8. endless expense 45
    Post

    Going Commando Build

    I like it!
    Post by: endless expense 45, Sep 23, 2009 in forum: Builds and Fabricators Forum
  9. endless expense 45
    Post

    Going Commando Build

    Looks good,Glad to see you out on the trail with it.
    Post by: endless expense 45, Sep 21, 2009 in forum: Builds and Fabricators Forum
  10. endless expense 45
    Post

    Going Commando Build

    Looks good,can't wait to wheel with it!You need to paint it NEON GREENR)
    Post by: endless expense 45, Aug 13, 2009 in forum: Builds and Fabricators Forum
  11. endless expense 45
    Post

    Hard top hoist

    I priced the stuff to do a hand winch the 3 pullys,50' of 3/16 cable,boat winch and side wall mount,eye bolts to hang the pullys ,lag screws ,and...
    Post by: endless expense 45, Jul 15, 2009 in forum: Builds and Fabricators Forum
  12. endless expense 45
    Thread

    Hard top hoist

    I built this over the weekend to remove the hard top on my wife's new to her TJ. Total Build cost was $130.00 sure beats $400.00 for a Lange...
    Thread by: endless expense 45, Jul 14, 2009, 3 replies, in forum: Builds and Fabricators Forum
  13. endless expense 45
    Profile Post

    I see you!

    I see you!
    Profile Post by endless expense 45 for JeepinWife2007, Mar 16, 2009
  14. endless expense 45
    Post

    Grade 8 or 5

    When in doubt always go grade 8,and they just plain look good to!
    Post by: endless expense 45, Oct 1, 2008 in forum: Builds and Fabricators Forum
  15. endless expense 45
    Post

    D44 rebuild

    :iagree: and if you can get the old bearings off in one piece then make them slip fit with a die grinder so you can change the carrier shims...
    Post by: endless expense 45, Sep 17, 2008 in forum: Flat Fender Tech
  16. endless expense 45
    Post

    Bye Bye D27 hello D30

    I promised her a ride when I got done and test drove it, I think this is her way of saying I need to hurry upR)R) I hope to get the brakes done...
    Post by: endless expense 45, Sep 17, 2008 in forum: Builds and Fabricators Forum
  17. endless expense 45
    Post

    Bye Bye D27 hello D30

    I can agree with that! I would say it looks good but then I supplied most of the parts,the shop,and labor so I think it is great!R)R)
    Post by: endless expense 45, Sep 14, 2008 in forum: Builds and Fabricators Forum
  18. endless expense 45
    Thread

    Saginaw Steering box help!

    I decided to drill and tap my steering box for hydraulic assist and I am having a slight problem getting the recirculating balls back into the...
    Thread by: endless expense 45, Aug 24, 2008, 2 replies, in forum: Intermediate CJ-5/6/7/8
  19. endless expense 45
    Post

    Propane Install

    Worked on it yesterday I wasn't out of propane the rotor button came loose and knocked a hole in the back of the dist. cap.Just one of those...
    Post by: endless expense 45, Aug 21, 2008 in forum: Builds and Fabricators Forum
  20. endless expense 45
    Post

    Propane Install

    I just hope they get alongR)R)I've still got alot of tuning to do I burnt 8 Gallons of propane in 2 hours:? that ain't gonna work unless a propane...
    Post by: endless expense 45, Aug 18, 2008 in forum: Builds and Fabricators Forum
Showing results 1 to 20 of 121 Next >
Search Again
Page 1 of 7
New Posts