1. Registration trouble? Please use the "Contact Us" link at the bottom right corner of the page and your issue will be resolved.
    Dismiss Notice

Search Results

Search Again
  1. goofyjumper
    Post

    Converting a 5 to a 6, an abbreviated story.

    My tilt column is mounted using the brackets from a '76 and newer CJ retro-fitted to my tub. Sorry, no close up shots. I'm running 5.13 gearing...
    Post by: goofyjumper, Jun 19, 2013 in forum: Intermediate CJ-5/6/7/8
  2. goofyjumper
    Post

    Converting a 5 to a 6, an abbreviated story.

    Yes, that is correct. In that photo there is about a 1.5" body lift.
    Post by: goofyjumper, May 16, 2013 in forum: Intermediate CJ-5/6/7/8
  3. goofyjumper
    Post

    Converting a 5 to a 6, an abbreviated story.

    I like it a lot. I went with a 16" stick which brings the shift knob right up to dash height. I went this route because the transmission (TH400)...
    Post by: goofyjumper, May 16, 2013 in forum: Intermediate CJ-5/6/7/8
  4. goofyjumper
    Post

    Converting a 5 to a 6, an abbreviated story.

    Visually, when I bought my CJ it looked pretty good. The reality was the opposite. Three of the body mounts had rusted away and crushed through...
    Post by: goofyjumper, May 15, 2013 in forum: Intermediate CJ-5/6/7/8
  5. goofyjumper
    Post

    Converting a 5 to a 6, an abbreviated story.

    For low center of gravity jeeps, articulation is switched from up travel to down.... though at the moment I haven't gotten the down travel thing...
    Post by: goofyjumper, May 14, 2013 in forum: Intermediate CJ-5/6/7/8
  6. goofyjumper
    Thread

    Converting a 5 to a 6, an abbreviated story.

    In December of 2011 I decided to purchase an intermediate CJ-5 with the idea of making a very capable off road jeep. I very quickly realized that...
    Thread by: goofyjumper, May 10, 2013, 20 replies, in forum: Intermediate CJ-5/6/7/8
  7. goofyjumper
    Post

    '74 CJ 5 Hood, Grill, and Fender Compatibility to '94 YJ Tub

    Thank you everyone for the honest opinions. I'll probably just stick with the CJ Tub and Frame and beef it up.
    Post by: goofyjumper, Jan 15, 2012 in forum: Intermediate CJ-5/6/7/8
  8. goofyjumper
    Post

    '74 CJ 5 Hood, Grill, and Fender Compatibility to '94 YJ Tub

    I guess I am wondering where the legal gray area is on this. Frame swaps are very common and nobody questions the legality of that. Body swaps...
    Post by: goofyjumper, Jan 14, 2012 in forum: Intermediate CJ-5/6/7/8
  9. goofyjumper
    Post

    '74 CJ 5 Hood, Grill, and Fender Compatibility to '94 YJ Tub

    Here's a second question to go along with the first... If I were to just swap body tubs, I am sure I could get away with retaining my '74 vin....
    Post by: goofyjumper, Jan 13, 2012 in forum: Intermediate CJ-5/6/7/8
  10. goofyjumper
    Thread

    '74 CJ 5 Hood, Grill, and Fender Compatibility to '94 YJ Tub

    I am toying with the idea of purchasing a YJ body and frame for dirt cheap ($1,000) and swapping all my CJ stuff on to it. If I swap the Hood,...
    Thread by: goofyjumper, Jan 13, 2012, 7 replies, in forum: Intermediate CJ-5/6/7/8
  11. goofyjumper
    Post

    Dual Front Fuel Tanks and 1 Fill tube.

    I considered one long tank spanning from the driver's to passenger side, but was worried that in off camber situations on a trail that all the...
    Post by: goofyjumper, Jan 11, 2012 in forum: Early CJ5 and CJ6 Tech
  12. goofyjumper
    Thread

    Dual Front Fuel Tanks and 1 Fill tube.

    I've looked through the forum and seen that the dual tank topic has been well discussed. For suspension reasons, I am exploring the idea of...
    Thread by: goofyjumper, Jan 11, 2012, 8 replies, in forum: Early CJ5 and CJ6 Tech
  13. goofyjumper
    Post

    AMC 401 and 304 parts compatibility:

    Yep, body is off, there were some frame and body issues, so I took it apart. Will be patching a lot of rust and repairing a few cracks in the...
    Post by: goofyjumper, Dec 30, 2011 in forum: Intermediate CJ-5/6/7/8
  14. goofyjumper
    Post

    AMC 401 and 304 parts compatibility:

    All good advice so far. Thank you! The engine is prone to overheating. Bad radiator and no shroud. Both problems that are going to be fixed....
    Post by: goofyjumper, Dec 30, 2011 in forum: Intermediate CJ-5/6/7/8
  15. goofyjumper
    Post

    AMC 401 and 304 parts compatibility:

    Thank you for the replies. The 401 does run fairly well, I just want to add reliability to it by doing a rebuild. It leaks oil from almost every...
    Post by: goofyjumper, Dec 30, 2011 in forum: Intermediate CJ-5/6/7/8
  16. goofyjumper
    Thread

    AMC 401 and 304 parts compatibility:

    Hi, I recently purchased a "74" CJ 5 that I was told had a 304 in it. I ordered a complete rebuild kit, timing chain and gear kit, cam, rocker,...
    Thread by: goofyjumper, Dec 30, 2011, 10 replies, in forum: Intermediate CJ-5/6/7/8
Showing results 1 to 16 of 16
Search Again
New Posts