1. Registration trouble? Please use the "Contact Us" link at the bottom right corner of the page and your issue will be resolved.
    Dismiss Notice

Brake flluid flowing out the top of the master cylinder

Discussion in 'Intermediate CJ-5/6/7/8' started by Conan, Nov 20, 2011.

  1. Nov 20, 2011
    Conan

    Conan New Member

    Montgomery, Alabama
    Joined:
    Jun 6, 2010
    Messages:
    34
    I call myself having rebuilt my brakes, replacing the brake lines, cylinders, and shoes at every wheel. I did this because, while driving my '75 CJ5 one day, the pedal, which had been getting lower, went to the floor. I got out of the Jeep and the master cylinder was empty. Anyway, I'm outside trying to bleed the brakes, and every time my assistant steps on the brake pedal, brake fluid leaks out of the middle of the front and the middle of the rear of the master cylinder cover.

    Can anyone tell me what's going on? Do I have a bad seal between the master cylinder and the cap and need to replace both?

    I appreciate any help y'all can give.
     
  2. Nov 20, 2011
    nickmil

    nickmil In mothballs.

    Happy Valley, OR
    Joined:
    Sep 23, 2002
    Messages:
    12,529
    A good master cylinder will get a quick vertical squirt out of the vent/compensating port. If your cap seal is bad it will leak out as you describe. Is one reservoir level getting higher as you operate the master cylinder? If so the mc is bypassing (leaking internally) and needs rebuilt or replaced.
     
  3. Nov 21, 2011
    cookieman

    cookieman Member

    Colton,Calif
    Joined:
    Jan 31, 2005
    Messages:
    302
    Sound more like,you got air in master cylinder. You need to pump the air out of system.
     
  4. Nov 21, 2011
    nickmil

    nickmil In mothballs.

    Happy Valley, OR
    Joined:
    Sep 23, 2002
    Messages:
    12,529
    Always looking to learn something new. How will air in the m/c cause a fluid leak out the cap?
     
  5. Nov 21, 2011
    OleBlue

    OleBlue Sponsor

    Tennessee
    Joined:
    Feb 14, 2010
    Messages:
    1,001
    Similar situation happened to me when a bled my brakes a few months back. I didn't have it overflow and go out from under the cap, but bubbles were clearly seen in the mc in the fluid. May have happened because I didn't bench bleed the mc first.
     
  6. Nov 21, 2011
    nickmil

    nickmil In mothballs.

    Happy Valley, OR
    Joined:
    Sep 23, 2002
    Messages:
    12,529
    In your case the air didn't cause the fluid to leak out the cap so the question remains. How will air in the m/c cause a fluid leak out of the cap.
     
  7. Nov 21, 2011
    cookieman

    cookieman Member

    Colton,Calif
    Joined:
    Jan 31, 2005
    Messages:
    302
    When you have air in lines or m/c. And when you remove pressure from the pedal the air pushed the fluid back, and it hits the top of the lid and run along top and under gasket. And out and run down the sides.
     
  8. Nov 21, 2011
    Patrick

    Patrick Super Moderator Staff Member

    Los Alamos, NM
    Joined:
    Sep 22, 2002
    Messages:
    8,360
    That's something I've never seen before.
     
  9. Nov 21, 2011
    OleBlue

    OleBlue Sponsor

    Tennessee
    Joined:
    Feb 14, 2010
    Messages:
    1,001
    As I stated, I had a similar situation but mine didn't overflow. I didn't want to overfill, but I do recall seeing fluid on the bottom side of the gasket from the rise in fluid. Fwiw my mc is a new dorman.
     
  10. Nov 21, 2011
    Hawkes

    Hawkes Member

    Nova scotia
    Joined:
    Jun 18, 2003
    Messages:
    490
    This is what I experienced when I put a new master on this year. Bend the hold down strap down in the middle so it puts more pressure on the cover. I've got mine tight enough I use a screwdriver to release it. Funny how modern plastic covers with little snaps seal so much better. Mine doesn't leak anymore.

    I also removed the residual valves, probably made the back spray worse.
     
  11. Nov 22, 2011
    nickmil

    nickmil In mothballs.

    Happy Valley, OR
    Joined:
    Sep 23, 2002
    Messages:
    12,529
    Me neither. (the following is not directed at you Patrick, I know you know how this stuff works)

    The drum brake retracting springs will pull the shoes back, hence the pistons in the m/c back in their bores, and cause the fluid to go back to the m/c reservoir, which it's designed to do. Similar things will happen when the pistons retract back in their bores in disc brake calipers. In either case the fluid will not "squirt" up. In 25 years of working on brake systems, prototyping brake systems, and teaching brake systems, I've never seen air in the system cause it to squirt out of the m/c. I am interested in the theory WHY, or HOW this could have happened.
    Might want to go back and re-read my first reply folks as I suspect that's what was really going on. Besides, if the cap and seal or gasket is making a good seal, it can't leak from the cap anyway.
     
    Last edited: Nov 22, 2011
New Posts