1. Registration trouble? Please use the "Contact Us" link at the bottom right corner of the page and your issue will be resolved.
    Dismiss Notice

416 Parts sources?

Discussion in 'Jeep Trailer Tech' started by sparky, Jul 8, 2005.

  1. Jul 8, 2005
    sparky

    sparky Sandgroper Staff Member Founder

    Perth, WA
    Joined:
    Sep 20, 2002
    Messages:
    9,221
    So, since we have this new forum section.

    What are good sources for wheel bearings, brake shoes and that sorta thing for a M416?

    I need to get busy with mine!

    Planning to have the tub blasted inside and Duraback it (hopefully this month or early next).

    Then bearings, hand brake, more permanent wiring. Retrofit my mil spec tail lights with 12V lights and take the ugly Wal-Mart specials off and put a good hookup on the TJ and CJ-5. :D
     
    sparky, Jul 8, 2005
    #1
  2. Jul 8, 2005
    Boyink

    Boyink Super Moderator Staff Member

    Tulsa, OK
    Joined:
    Sep 20, 2002
    Messages:
    6,197
    Aren't 416 bearings /shoes etc just D27 9" stuff?
     
    Boyink, Jul 8, 2005
    #2
  3. Jul 8, 2005
    sparky

    sparky Sandgroper Staff Member Founder

    Perth, WA
    Joined:
    Sep 20, 2002
    Messages:
    9,221
    Dunno, that's why I'm asking.

    If it is then I should be familiar with it. ;)

    I know very little about my trailer's mechanicals. Going to learn soon.
     
    sparky, Jul 8, 2005
    #3
  4. Jul 8, 2005
    jpflat2a

    jpflat2a what's that noise?

    Hermosa, SD
    Joined:
    Jul 30, 2003
    Messages:
    8,517
    should be the early D25/D27 as Mike said
    smaller diam wheel bearings and seals
     
    jpflat2a, Jul 8, 2005
    #4
  5. Jul 8, 2005
    sparky

    sparky Sandgroper Staff Member Founder

    Perth, WA
    Joined:
    Sep 20, 2002
    Messages:
    9,221
    Sweet!

    I can handle that. :D
     
    sparky, Jul 8, 2005
    #5
  6. Dec 3, 2006
    lten1063

    lten1063 New Member

    Joined:
    Dec 3, 2006
    Messages:
    2
    You might try G503.com forums and scroll to the M416 threads.

    later Joe
     
    lten1063, Dec 3, 2006
    #6
  7. Dec 4, 2006
    Walldog

    Walldog New Member

    ME
    Joined:
    Jul 13, 2005
    Messages:
    41
    Walldog, Dec 4, 2006
    #7
  8. Dec 4, 2006
    sparky

    sparky Sandgroper Staff Member Founder

    Perth, WA
    Joined:
    Sep 20, 2002
    Messages:
    9,221
    sparky, Dec 4, 2006
    #8
  9. Dec 9, 2006
    CoRubicon

    CoRubicon New Member

    Joined:
    Sep 19, 2006
    Messages:
    4
    I just went through the brakes and bearings in my M416, this is what I did.

    Bearings and seals came from the local bearing house.

    The thrust washers, lock washers and nuts for the wheel bearings are the same as 41 to 86 CJ stuff.

    I couldn't find anybody who knew for sure what brake shoes fit, so I had mine re-lined at the local brake and clutch shop for $28.

    My brake cable was also seized up, I got a new one from Mullins jeep parts for $47.50

    Hope that helps.

    Jim
     
    CoRubicon, Dec 9, 2006
    #9
New Posts