1. Registration trouble? Please use the "Contact Us" link at the bottom right corner of the page and your issue will be resolved.
    Dismiss Notice

What Did You Do To Your Jeep Today?

Discussion in 'Builds and Fabricators Forum' started by Focker, Jul 23, 2016.

  1. Nov 26, 2021
    Downs

    Downs Rattlecan All The Things!

    Hunt County Texas
    Joined:
    Jul 25, 2020
    Messages:
    579
    There are pusher fans out there. I'm sure this is one. But supposedly pusher fans are less efficient than puller fans when it comes to radiators. I dunno I'm not an engineer lol
     
    bigjohn likes this.
  2. Nov 26, 2021
    bigjohn

    bigjohn Active Member

    Kelso Wa
    Joined:
    Mar 18, 2010
    Messages:
    1,054
    Ah this is good to know! This 258 is very tired with no real cooling issues. This is for piece of mind mostly.
     
    Fireball likes this.
  3. Nov 26, 2021
    bigjohn

    bigjohn Active Member

    Kelso Wa
    Joined:
    Mar 18, 2010
    Messages:
    1,054
    The electric fan has been my primary cooling fan since I’m guessing around 2008/9. At the time I wasn’t aware the contour/Taurus fan was a thing, and this fan really didn’t fit on the engine side of the radiator. So I reversed the fan blade for front mounting (also incredibly tight) which does kill some efficiency vs pulling. I had bought a thermostat switch for it back then but was the wrong size. All of these years the fan has just been on a switch. Turn it on in town, turn it off on the freeway.
     
    dozerjim and Fireball like this.
  4. Nov 29, 2021
    Andrew Theros

    Andrew Theros Member 2023 Sponsor 2022 Sponsor

    Los Osos, CA
    Joined:
    Feb 24, 2021
    Messages:
    393
    AE6E18C0-F627-4E4A-AAE7-BFE4B5672685.jpeg B630BB53-10FD-4E3E-89BE-36A9BA2DA89E.jpeg Got down to the block, now it’s time to clean…check/rebuild the oil pump, and replace the distributor gear and fuel pump eccentric.
    I’ve got a little time, bolt kit is not supposed to ship ‘till Thursday.
    Also, a couple broken bolts in the timing cover, one water pump and 1 oil pan (like that when I got here, honest!).
     
    Downs likes this.
  5. Nov 29, 2021
    Desert Runner

    Desert Runner Member 2024 Sponsor 2022 Sponsor

    Hickory, Pa
    Joined:
    Sep 11, 2005
    Messages:
    806
    sure it was :p
     
    Twin2 likes this.
  6. Nov 29, 2021
    boopiejones

    boopiejones I can’t drive 55

    California east bay
    Joined:
    Mar 16, 2020
    Messages:
    545
    Installed a new radiator a few weeks ago. Finally got around to building a shroud for it today. Idled for a about 10 minutes while I messed around with my steering stops, and the temperature held steady. Normally the temperature rises about 15-20 degrees after idling for an extended period, so the shroud certainly seems to help.
    AB5E434B-34B8-4138-B5F0-C2A7B5E9712C.jpeg
     
  7. Nov 29, 2021
    Andrew Theros

    Andrew Theros Member 2023 Sponsor 2022 Sponsor

    Los Osos, CA
    Joined:
    Feb 24, 2021
    Messages:
    393
    Mmmm, sailor Jerry!
    Can’t do that brown stuff anymore, have to pay too much later but I used to enjoy some Sailor Jerry with coke!

    Oh yeah, Jeep looks good too!
     
  8. Nov 30, 2021
    Buildflycrash

    Buildflycrash More or Less in Line. 2024 Sponsor 2022 Sponsor

    Gulf Breeze FL...
    Joined:
    Jun 5, 2007
    Messages:
    3,559
    Was out of town all last week visiting for the holiday. Got the tire carrier all welded up last night.

    [​IMG]

    Put a 33 up there and found I need a little adjustment.

    [​IMG]
     
    73 cj5, 3b a runnin, Rich M. and 3 others like this.
  9. Dec 2, 2021
    Downs

    Downs Rattlecan All The Things!

    Hunt County Texas
    Joined:
    Jul 25, 2020
    Messages:
    579
    Installed a JB Customs twin stick shifter for the Dana20. Had an issue with going into 4low, I had 2wd, 4wd, 2low but no 4lo, called customer service and they told me that some of the short clocked shifters on the T150/D20 combo would need the channel on the shifter sticks elongated a little due to a slight difference in height on some D20 shifter mounts causing them to run out of travel before the interlock pills were in the right spots. I pulled the levers out took the die grinder to them now I have 4low access. Made a quick ugly cover as the one that came with it wasn't large enough to cover the hole, but it works. Much nicer not having all that slop in the shifter linkage, much simpler design. They should have never moved away from the simple D18 twin stick setup.
     
  10. Dec 2, 2021
    Jw60

    Jw60 Sitting up n buckled down. 2024 Sponsor 2023 Sponsor 2022 Sponsor

    Sedalia MO.
    Joined:
    Apr 8, 2008
    Messages:
    4,716
    It would be hard to make a dana 20 shift like an 18 with the gears being on independent shafts. The issue is that the gears are not in phase in all gear positions.
     
  11. Dec 2, 2021
    Downs

    Downs Rattlecan All The Things!

    Hunt County Texas
    Joined:
    Jul 25, 2020
    Messages:
    579
    I just meant retaining the simpler twin stick configuration not necessarily shifting exactly like a D18. The single stick setup just had too many pivot/wear points IMO. This twin stick only has 2 pivots per shifter now, much simpler and a hell of a lot less slop. This was even after replacing everything I could easily on the single stick shifter.
     
    Ol Fogie and Jw60 like this.
  12. Dec 3, 2021
    73 cj5

    73 cj5 Not ready for the junkyard yet

    Clinton, Mississippi
    Joined:
    Jan 10, 2014
    Messages:
    2,137
    Performed a little weight reduction. That winch never fit well up there, I had to butcher the mount to make it fit, and I was bored. It'll be better off on something else.

    [​IMG]

    I ended up buying this floor jack to take on trips. My old 3 ton jack was leaking down and the handle disappeared after someone borrowed it. :confused:

    [​IMG]
     
  13. Dec 5, 2021
    Buildflycrash

    Buildflycrash More or Less in Line. 2024 Sponsor 2022 Sponsor

    Gulf Breeze FL...
    Joined:
    Jun 5, 2007
    Messages:
    3,559
    Had a little time today to work on the CJ. Finished painting the bumper, tire carrier and rear crossmember.

    [​IMG]

    Bolted on the fuel tank skid to put the nuts on the new crossmember. Marked and drilled. When welding on the nuts I used these counter sunk bolts to center the nuts in the hole.

    [​IMG]

    Now today’s problem. Either my frame has become tweaked a bunch or the body has shifted. I’m thinking the frame.

    [​IMG]
     
    Ol Fogie and Fireball like this.
  14. Dec 6, 2021
    Lockman

    Lockman OK.....Now I Get It . 2024 Sponsor 2023 Sponsor 2022 Sponsor

    Silver Hill,...
    Joined:
    Dec 4, 2018
    Messages:
    2,698
    Yeah..... That's quite a bit ?
     
  15. Dec 6, 2021
    Norcal69

    Norcal69 Out of the box thinker 2024 Sponsor 2023 Sponsor 2022 Sponsor

    Northern California
    Joined:
    Sep 6, 2014
    Messages:
    3,547
    Its likely both. :p
    The first Rubicon trip changes the driver and the jeep forever.......
     
    Buildflycrash likes this.
  16. Dec 6, 2021
    ITLKSEZ

    ITLKSEZ Hope for the best, prepare for the worst

    Liberty Lake, WA
    Joined:
    Aug 13, 2015
    Messages:
    6,656
    It’s possible that neither could be. These frames are so flexy, it could be a difference in floor flatness or resting spring heights. Try throwing a jack under the RR before putting it together.
     
    Buildflycrash likes this.
  17. Dec 6, 2021
    ITLKSEZ

    ITLKSEZ Hope for the best, prepare for the worst

    Liberty Lake, WA
    Joined:
    Aug 13, 2015
    Messages:
    6,656
    Our first plowable snow is on its way. Time to make the 3b ugly(er) again with a tire change and hook up the plow.

    [​IMG]
     
  18. Dec 6, 2021
    Lockman

    Lockman OK.....Now I Get It . 2024 Sponsor 2023 Sponsor 2022 Sponsor

    Silver Hill,...
    Joined:
    Dec 4, 2018
    Messages:
    2,698
    Yeah...... There also call'n for 12 feet in the mountains.......Of Hawaii.:shock:
     
  19. Dec 6, 2021
    colojeepguy

    colojeepguy Colorado Springs

    At the foot of...
    Joined:
    Apr 4, 2010
    Messages:
    7,110
    Everyones makiing a big deal about that...it snows on the big island all the time. The volcanoes are something like 13000 ft elevation.
     
  20. Dec 6, 2021
    colojeepguy

    colojeepguy Colorado Springs

    At the foot of...
    Joined:
    Apr 4, 2010
    Messages:
    7,110
    Changed out a leaky oil pressure sender today...decided to pull the alternator for easier access. Boy is it grungy behind there! 51 years worth of crud!
    20211206_084425.jpg
    Of course my t fitting snapped, luckily I found a replacement in my toolbox!
    20211206_084412.jpg
     
New Posts