1. Registration trouble? Please use the "Contact Us" link at the bottom right corner of the page and your issue will be resolved.
    Dismiss Notice

D44 Bearings

Discussion in 'Early CJ5 and CJ6 Tech' started by Howard Eisenhauer, Mar 24, 2020.

  1. Mar 24, 2020
    Howard Eisenhauer

    Howard Eisenhauer Administrator Staff Member

    Tantallon, Nova...
    Joined:
    Nov 22, 2003
    Messages:
    8,102
    What's the difference size wise / PNs between tapered & flanged axle carrier bearings?
     
  2. Mar 24, 2020
    FinoCJ

    FinoCJ 1970 CJ5 Staff Member

    Bozeman, MT
    Joined:
    Jul 18, 2013
    Messages:
    5,593
    I feel like TlmE and I went through this a while back when i did the locker install...I might be able to find some of the info, or hopefully he can chime in? My gut feeling is that they are the same?
     
  3. Mar 26, 2020
    linckeil

    linckeil Member

    Danbury CT
    Joined:
    Aug 19, 2004
    Messages:
    492
    timken carrier bearing and race part numbers for my flanged 44 is 25590 and 25523, respectively. not sure about a tapered 44, but i imagine it is the same.
     
  4. Mar 26, 2020
    47v6

    47v6 junk wrecker! 2023 Sponsor 2022 Sponsor

    USA
    Joined:
    Oct 25, 2006
    Messages:
    5,798
    They are NOT the same. 30 spline requires a different bearing than 10/19 spline axles.
     
    fhoehle likes this.
  5. Mar 26, 2020
    Fireball

    Fireball Well-Known Member 2024 Sponsor 2023 Sponsor 2022 Sponsor

    Pullman, WA
    Joined:
    Feb 9, 2018
    Messages:
    5,622
    Like 47v6 says.... I swear I had heard the larger 30 spline flanged axles require a bearing with a larger ID, but use the same outer race.
     
    47v6 likes this.
  6. Mar 26, 2020
    Howard Eisenhauer

    Howard Eisenhauer Administrator Staff Member

    Tantallon, Nova...
    Joined:
    Nov 22, 2003
    Messages:
    8,102
    My problem is I want to (finally!) install my e-locker but the cones I bought don't fit :cry:, I'm thinking they need to be the later pieces, with a pn I can look up the specs to see if they'll fit.
     
  7. Mar 26, 2020
    linckeil

    linckeil Member

    Danbury CT
    Joined:
    Aug 19, 2004
    Messages:
    492
    so i have a spare carrier from a 30 spline flanged 44. i just measured the diameter where the bearing presses on and it is 1.800". the timken bearing part number i gave above (25590) has an ID of 1.796" resulting in a press fit. the race as i mentioned is part number 25523.

    as i said, i can't confirm what a tapered 10 or 19 spine 44 uses. but a quick search tells me it takes a 25577 bearing (ID of 1.688") and the same 25523 race.

    so the "cones" or "races" should be the same between both axles. it's the bearing ID that is different. what part number cones do you have?
     
  8. Mar 26, 2020
    linckeil

    linckeil Member

    Danbury CT
    Joined:
    Aug 19, 2004
    Messages:
    492
    edit to my terminology above - i was thinking "cup" when saying "cone". i just always use "bearing" and "race". anyway, the bearings (cones) are in fact different, the races (cups) are the same.
     
  9. Mar 26, 2020
    Howard Eisenhauer

    Howard Eisenhauer Administrator Staff Member

    Tantallon, Nova...
    Joined:
    Nov 22, 2003
    Messages:
    8,102
    Got it- Thanks :)
     
New Posts