1. Registration trouble? Please use the "Contact Us" link at the bottom right corner of the page and your issue will be resolved.
    Dismiss Notice

When Pulling The F134 Motor?

Discussion in 'Early CJ5 and CJ6 Tech' started by mickeykelley, Dec 13, 2017.

  1. Dec 13, 2017
    mickeykelley

    mickeykelley Well-Known Member

    Republic of Texas
    Joined:
    Oct 10, 2015
    Messages:
    1,900
    When pulling the F134, about how far forward does the engine need to come to clear the tranny, etc.
     
  2. Dec 13, 2017
    Howard Eisenhauer

    Howard Eisenhauer Administrator Staff Member

    Tantallon, Nova...
    Joined:
    Nov 22, 2003
    Messages:
    8,102
    Bellhousing on or off?

    I unbolt the bellhousing from the engine, put a little forward /up strain on the engine & give it a good shake- it'll pop forward till it hits the crossmember & then can be lifted up.
     
    ITLKSEZ likes this.
  3. Dec 13, 2017
    mickeykelley

    mickeykelley Well-Known Member

    Republic of Texas
    Joined:
    Oct 10, 2015
    Messages:
    1,900
    Just undid the 4 engine bolts. Was hoping to get it out that way.
     
  4. Dec 13, 2017
    Glenn

    Glenn Kinda grumpy old man Staff Member

    Apopka, Fl
    Joined:
    Sep 21, 2002
    Messages:
    12,367
    Remember at a minimum it has to come forward far enough for the transmission input shaft to be disengaged from the clutch.
     
  5. Dec 13, 2017
    Daryl

    Daryl Sponsor

    Bonney Lake, WA
    Joined:
    May 25, 2006
    Messages:
    2,871
    Best to remove your radiator first if you haven't already done so. I usually just pull the grille.
     
    Jrobz23 likes this.
  6. Dec 13, 2017
    GeoffreyL

    GeoffreyL Well-Known Member

    moorestown, nj
    Joined:
    Aug 1, 2012
    Messages:
    1,521
    I pull the grill so I have more room for my engine hoist, it's really quick to do.
     
  7. Dec 13, 2017
    mickeykelley

    mickeykelley Well-Known Member

    Republic of Texas
    Joined:
    Oct 10, 2015
    Messages:
    1,900
    Yep getting it out with the clutch on and the water pump pully/crank pully had to twist etc. Putting it back in, I may just pull the grill. I decided to get the 2 ton Harbor Freight chain hoist (2 ton Manual Chain Hoist) with it attached to my bobcat forks with the boom all the way in the high position. And yes I had the safety brace in place. It actually worked better than engine hoists I've used in the past and after a 20% off it was only $56. The chain moves very little for the amount of pulls but that actually worked well. In any event, it's out and at the rebuilders. Now a 4-6 week wait but he does a number of these F 134's and the L226's, which is next to pull the wagon motor. In fact he had one he just finished which had been in a ambulance jeep. It had the magneto and a few other different military items.
     
  8. Dec 13, 2017
    Glenn

    Glenn Kinda grumpy old man Staff Member

    Apopka, Fl
    Joined:
    Sep 21, 2002
    Messages:
    12,367
    A 226 in a Jeep ambulance? I know they put the OHC 230 in the M715 and M725, didn't know there was an application for a 226. Or am I misreading and not realizing you meant the 134 in a M170?
     
  9. Dec 13, 2017
    mickeykelley

    mickeykelley Well-Known Member

    Republic of Texas
    Joined:
    Oct 10, 2015
    Messages:
    1,900
    Not the 226, the 134.
     
  10. Dec 13, 2017
    Glenn

    Glenn Kinda grumpy old man Staff Member

    Apopka, Fl
    Joined:
    Sep 21, 2002
    Messages:
    12,367
    :coffee::)
     
  11. Dec 14, 2017
    PeteL

    PeteL If it wasn't for physics, and law enforcement... 2024 Sponsor 2023 Sponsor 2022 Sponsor

    Hills of NH
    Joined:
    Aug 3, 2003
    Messages:
    9,754
    Magneto?
     
  12. Dec 14, 2017
    mickeykelley

    mickeykelley Well-Known Member

    Republic of Texas
    Joined:
    Oct 10, 2015
    Messages:
    1,900
    Yes that's what he said and when I looked it, it was not a typical looking distributor. The top cap was flat and had holes for the plug wires to come out but we're not raised like normal caps.
     
    Last edited: Dec 14, 2017
  13. Dec 14, 2017
    Glenn

    Glenn Kinda grumpy old man Staff Member

    Apopka, Fl
    Joined:
    Sep 21, 2002
    Messages:
    12,367
    I'm sure it's the waterproof distributor that you saw.
     
  14. Dec 14, 2017
    Glenn

    Glenn Kinda grumpy old man Staff Member

    Apopka, Fl
    Joined:
    Sep 21, 2002
    Messages:
    12,367
  15. Dec 14, 2017
    Glenn

    Glenn Kinda grumpy old man Staff Member

    Apopka, Fl
    Joined:
    Sep 21, 2002
    Messages:
    12,367
    Just FYI, there is an actual distributor cap under that metal cover and the coil is in the round fluted part of the distributor base.
     
  16. Dec 14, 2017
    wheelie

    wheelie beeg dummy 2024 Sponsor 2023 Sponsor

    York, PA
    Joined:
    Mar 6, 2004
    Messages:
    4,491
    The M38A1 had hinges on the bottom of the grill, I believe to make engine changes faster and maybe easier. If military design carries any weight for you, I'd call this an indicator as to the best and easiest way to pull the engine ......removing the grill.
     
  17. Dec 14, 2017
    Glenn

    Glenn Kinda grumpy old man Staff Member

    Apopka, Fl
    Joined:
    Sep 21, 2002
    Messages:
    12,367
    I totally agree with removing the grill, makes it much easier.
     
  18. Dec 14, 2017
    ITLKSEZ

    ITLKSEZ Hope for the best, prepare for the worst

    Liberty Lake, WA
    Joined:
    Aug 13, 2015
    Messages:
    6,656
    You can even do it without unhooking any wiring. :D

    [​IMG]
     
    GeoffreyL and Daryl like this.
  19. Dec 14, 2017
    PeteL

    PeteL If it wasn't for physics, and law enforcement... 2024 Sponsor 2023 Sponsor 2022 Sponsor

    Hills of NH
    Joined:
    Aug 3, 2003
    Messages:
    9,754
    x2. 24 volts, waterproof, and RF shielded.
     
  20. Dec 14, 2017
    mickeykelley

    mickeykelley Well-Known Member

    Republic of Texas
    Joined:
    Oct 10, 2015
    Messages:
    1,900
    I don't remember the plug wire having any screw on threads. They were just holes the thickness of plug wires. But I wasn't really studying it that close. That's just what the rebuilder said and he's an older guy with sh#t ton of experience.
     
New Posts