1. Registration trouble? Please use the "Contact Us" link at the bottom right corner of the page and your issue will be resolved.
    Dismiss Notice

V6 Radiators

Discussion in 'Early CJ5 and CJ6 Tech' started by FinoCJ, Nov 23, 2017.

Page 2 of 2
  1. Nov 24, 2017
    Rozcoking23

    Rozcoking23 RUN & GET BIT! 2024 Sponsor

    Stockton, CA
    Joined:
    Mar 29, 2008
    Messages:
    842
    The one you have listed is what I finally ended up using. Its a direct bolt in, used the same hoses as my original. I have no issues with it at all, keeps everything kool, even when it was over 100 degrees here this summer.
     
    Rozcoking23, Nov 24, 2017
    #21
  2. Nov 24, 2017
    wheelie

    wheelie beeg dummy 2024 Sponsor 2023 Sponsor

    York, PA
    Joined:
    Mar 6, 2004
    Messages:
    4,502
    Which one listed? Which post in this thread?
     
    wheelie, Nov 24, 2017
    #22
  3. Nov 25, 2017
    Rozcoking23

    Rozcoking23 RUN & GET BIT! 2024 Sponsor

    Stockton, CA
    Joined:
    Mar 29, 2008
    Messages:
    842
    Rozcoking23, Nov 25, 2017
    #23
    wheelie and FinoCJ like this.
  4. Nov 25, 2017
    oldtime

    oldtime oldtime

    St. Charles,...
    Joined:
    Aug 14, 2006
    Messages:
    3,479
    I also have a couple V-6 radiators in need of new cores.
    Any one on this forum have radiator shop experience in the St Louis area ?
    Any suggestions on what kind or who makes the best replacement cores ?
     
    oldtime, Nov 25, 2017
    #24
  5. Nov 25, 2017
    wheelie

    wheelie beeg dummy 2024 Sponsor 2023 Sponsor

    York, PA
    Joined:
    Mar 6, 2004
    Messages:
    4,502
    Thanks for the clarification.
     
    wheelie, Nov 25, 2017
    #25
  6. Nov 27, 2017
    FinoCJ

    FinoCJ 1970 CJ5 Staff Member

    Bozeman, MT
    Joined:
    Jul 18, 2013
    Messages:
    5,629
    Dropped the radiator off at the Colorado Radiator Repair shop recommended by a member of my local 4x4 club. So we'll see how it goes. They had a bunch of large equipment radiators being worked on - shop looked clean and organized. They are going to run a pressure test on it tomorrow - we'll see how that compares to the Grand Junction shop that ran a pressure test last week.

    There are a couple other shops that seem good like Sercks (thanks Doug) and A1 but their location wasn't as convenient. For anyone in the same boat down the line needing repair and not replacement...search options will be much better if you specify OTR/18wheeler and heavy equipment radiator. I'll give an update on my experience and when the jeep is up and running again. Got another project about to start on the jeep as well ...will post that up on my build thread.
     
    FinoCJ, Nov 27, 2017
    #26
  7. Nov 27, 2017
    Warloch

    Warloch Did you say Flattie??? Staff Member

    Falcon, CO
    Joined:
    Mar 4, 2003
    Messages:
    5,469
    For what its worth - I've used Potts Radiator down here in the Springs with good luck too.
     
    Warloch, Nov 27, 2017
    #27
Page 2 of 2
New Posts