1. Registration trouble? Please use the "Contact Us" link at the bottom right corner of the page and your issue will be resolved.
    Dismiss Notice

Car Jack Recomendations

Discussion in 'The Tool Shed' started by aallison, Jul 1, 2016.

  1. Jul 1, 2016
    aallison

    aallison 74 cj6, 76 cj5. Has anyone seen my screwdriver?

    Green Cove...
    Joined:
    Nov 24, 2006
    Messages:
    1,929
    Well, my old Sears jack has seen better days. It's not even a craftsman. Just "sears". It still pumps but when I try to lower it it suddenly releases and the load comes down fairly fast. It is not anywhere the controlled lowering I would like to have. I don't think I can rebuild it, but I might be able to but I don't know if it is even worth it.

    I've looked at NAPA, O'Rileys, and at the Harbor Freight ad. I know HF has some real spiffy aluminum jacks and they come with 4 and 5 star ratings. But I'm not convinced of the quality when it has a ton of weight on it.

    Not doing it for a job, just working on cars and jeeps. Don't need a real spendy jack.

    So, what do you guys recommend?
     
  2. Jul 1, 2016
    Mcruff

    Mcruff Earlycj5 Machinist

    Albertville, AL
    Joined:
    Sep 22, 2002
    Messages:
    5,349
    I have been using my 3ton Harbor freight steel jack for 3-4 years now. No problems, great jack,easy control and I paid $80 for it, wouldn't hesitate to buy another!
    Used on jeeps, cars and 2wd trucks. It's heavy, built like a tank.

    [​IMG]
     
    Last edited: Jul 1, 2016
    schneedrache and 73 cj5 like this.
  3. Jul 1, 2016
    73 cj5

    73 cj5 Not ready for the junkyard yet

    Clinton, Mississippi
    Joined:
    Jan 10, 2014
    Messages:
    2,137
    Agree with Mcruff, they are a bargain for 80 bucks.
     
  4. Jul 1, 2016
    timgr

    timgr We stand on the shoulders of giants. 2022 Sponsor

    Medford Mass USA
    Joined:
    Aug 10, 2003
    Messages:
    23,596
    When I looked into this a few years ago, I recall that the difference between precise control and not is a needle valve or ball valve, resp. The ball valve is a lot cheaper to make. That said, I bought a HF floor jack several years ago, and it's not the greatest at precise control. It has been plenty good at raising and lowering though. Maybe the newer ones are better.

    Back then the Hein-Warner jack was recommended, at nearly 5x the cost of the HF for the same stated capacity - Amazon.com: Hein-Werner HW93652 Blue Heavy Duty Service Jack - 3 Ton Capacity: Home Improvement
     
  5. Jul 1, 2016
    aallison

    aallison 74 cj6, 76 cj5. Has anyone seen my screwdriver?

    Green Cove...
    Joined:
    Nov 24, 2006
    Messages:
    1,929
    I like this one...
    https://www.amazon.com/Powerbuilt-620422E-Heavy-Duty-Triple/dp/B00336EN60?ie=UTF8&tag=toptenbest-20

    But the HF jack for $100 might work just as well. Especially since HF was recommended above.
    3 ton Low Profile Steel Heavy Duty Floor Jack with Rapid Pump®

    Tim, that is a nice jack. A little spendy at $470 but I'm sure it is a good one. I did not know about the differences in the valves. I'm not looking for precise control but I want something more than the slam down my current jack gives me.
     
  6. Jul 1, 2016
    Mcruff

    Mcruff Earlycj5 Machinist

    Albertville, AL
    Joined:
    Sep 22, 2002
    Messages:
    5,349
    Mine is pretty darn smooth.
     
  7. Jul 1, 2016
    Twin2

    Twin2 not him 2024 Sponsor 2023 Sponsor 2022 Sponsor

    Virginia Beach, VA
    Joined:
    Apr 28, 2011
    Messages:
    5,406
    have sears craftsman and it won't stay up , second one too . quality isn't there anymore
     
  8. Jul 1, 2016
    ITLKSEZ

    ITLKSEZ Hope for the best, prepare for the worst

    Liberty Lake, WA
    Joined:
    Aug 13, 2015
    Messages:
    6,648
    Check a farm store like TSC. Their prices aren't usually too far off of harbor freight, and quality seems to be a few notches higher on tools.
     
  9. Jul 1, 2016
    PeteL

    PeteL If it wasn't for physics, and law enforcement... 2024 Sponsor 2023 Sponsor 2022 Sponsor

    Hills of NH
    Joined:
    Aug 3, 2003
    Messages:
    9,730
    I have about six or eight of these in all sizes - all free from the dump….all work perfectly. I get so many of them I give them to friends.

    Nine times out of ten they just need the oil topped up, or to be burped. But folks loose a check ball or just don't even try. Fill it up, run it through a few full cycles with no load.

    Sometimes it's a particle of crud needs to be flushed out of the valves. Not rocket science, just unscrew the valve needle or cover plug, let it drain some fluid, put it back together. Don't lose the ball.
     
    Last edited: Jul 1, 2016
  10. Jul 1, 2016
    Admiral Cray

    Admiral Cray I want to do this again.. Staff Member

    Bainbridge...
    Joined:
    Sep 21, 2009
    Messages:
    204,346
    Might look at Costco...

    Mine has work perfect for over 10 years...
     
  11. Jul 1, 2016
    aallison

    aallison 74 cj6, 76 cj5. Has anyone seen my screwdriver?

    Green Cove...
    Joined:
    Nov 24, 2006
    Messages:
    1,929
    Thanks...I'll try that first just to see. But I already took it mostly apart last fall when it would not pump up, changed the fluid, etc. Now it goes up fine but down real quick. I did not take the check ball out.

    I'd rather fix this if I could than buy one.....
     
  12. Jul 1, 2016
    bkap

    bkap Gone, but not long gone.

    Tucson, AZ
    Joined:
    Sep 9, 2006
    Messages:
    784
    I bought this US General aluminum 3000 lbs racing jack from Harbor Freight probably 25+ years ago and it's still going strong, despite knocking around pickup beds, trailer tool boxes and all manner of dirt and paved race tracks. I've never even replaced the fluid. (May have topped it off once. Maybe.)

    [​IMG]

    On the other hand, my two-ton, USA-made Lincoln steel jack has been expensively rebuilt once in the relatively few years I've owned it and has since taken another dump. Junk.
     
  13. Jul 1, 2016
    w3srl

    w3srl All-around swell dude Staff Member

    Port Orange, FL
    Joined:
    Nov 6, 2002
    Messages:
    4,275
    I've had the 3-ton Cardboard Freight model for years and haven't had any issues with it. Operates as smooth as a baby's bottom.

    We also carry a 1-1/2 ton HF racing jack on our heavy rescue truck at work. Its nice low profile and rapid-pump feature make it awesome for rescue jobs. With that said I'd steer awaty from the aluminum ones just for longevity's sake.
     
  14. Jul 1, 2016
    ITLKSEZ

    ITLKSEZ Hope for the best, prepare for the worst

    Liberty Lake, WA
    Joined:
    Aug 13, 2015
    Messages:
    6,648
    When my girls were babies, their bottoms operated quite explosively.
     
    Twin2 and bkap like this.
  15. Jul 1, 2016
    Alex V.

    Alex V. Member

    Campbellsville, KY
    Joined:
    Mar 12, 2008
    Messages:
    408
    I've had a friend's Napa 2 1/4 ton jack borrowed for a year now - goes up fast until it meets a load, and releases nice and gradual. My in-laws bought me a Craftsman 2 1/4 tonner for Christmas but if I needed to buy one of my own I'd really consider Napa.
     
    FinoCJ likes this.
  16. Jul 1, 2016
    piffey263

    piffey263 Active Member

    Medford, OR
    Joined:
    Oct 16, 2008
    Messages:
    1,214
    Another vote for the Napa jack your friend has,

    My friend paid $200, goes by up nice, comes down.
     
  17. Jul 2, 2016
    supertrooper

    supertrooper Member

    moreno valley, ca
    Joined:
    Nov 12, 2007
    Messages:
    736
    i have a 3 1/2 ton arcan jack that i got at costco several years ago. it has never had any problems but its really heavy. the steel harbor freight jack that mcruff linked is supposed to be good.
     
  18. Jul 2, 2016
    58 willys

    58 willys Sponsor

    Millsboro, Delaware
    Joined:
    Jul 2, 2010
    Messages:
    939
    I have 2 of the NAPA branded 3 ton Jacks got on sale for a little less than $200 I believe they are made by Hein-Weber haven't had any trouble with them
     
  19. Jul 2, 2016
    sterlclan

    sterlclan Member 2022 Sponsor

    exploring the...
    Joined:
    Feb 21, 2009
    Messages:
    3,857
    have several hf jacks well worth the price.
     
  20. Jul 2, 2016
    GeoffreyL

    GeoffreyL Well-Known Member

    moorestown, nj
    Joined:
    Aug 1, 2012
    Messages:
    1,521
    I love the old sears jacks, I have two from back in the early 80's, just can't beat them if you ask me. I have no experience with the HF ones but their bottle jacks have always worked nice when I got them. I have a couple snap on ones too but I done use them cause they need rebuilt. They leak down over time.
     
New Posts