1. Registration trouble? Please use the "Contact Us" link at the bottom right corner of the page and your issue will be resolved.
    Dismiss Notice

Waldron exhaust arrived for 67 w/ dauntless

Discussion in 'Early CJ5 and CJ6 Tech' started by seven4eight, Nov 10, 2015.

  1. Nov 10, 2015
    seven4eight

    seven4eight Sponsor

    NE Ga
    Joined:
    Dec 20, 2013
    Messages:
    55
    Just wanted to give a shout out to Waldron, website says 6-8 weeks but I got my full system for 67 w/ 225 on the doorstep today 10 days after ordering. Looks incredible, solid quality welds etc. Customer service was great as well, would highly recommend. I'll follow up when mounted.
     
    seven4eight, Nov 10, 2015
    #1
  2. Nov 10, 2015
    Johns1967CJ5

    Johns1967CJ5 Sponsor

    Northern NJ
    Joined:
    Dec 5, 2013
    Messages:
    1,694
    Good to know. I ordered mine yesterday
     
    Johns1967CJ5, Nov 10, 2015
    #2
  3. Nov 11, 2015
    Uncle Vin

    Uncle Vin Member 2022 Sponsor

    Long Island, New...
    Joined:
    Sep 29, 2008
    Messages:
    348
    Did either of you go with a stainless system?
     
    Uncle Vin, Nov 11, 2015
    #3
  4. Nov 11, 2015
    Johns1967CJ5

    Johns1967CJ5 Sponsor

    Northern NJ
    Joined:
    Dec 5, 2013
    Messages:
    1,694
    I went with aluminized due to cost.
     
    Johns1967CJ5, Nov 11, 2015
    #4
  5. Nov 13, 2015
    army grunt

    army grunt Member

    Georga USA
    Joined:
    Feb 21, 2012
    Messages:
    269
    I found when I did mine adding a brace from the transmission down to the cross over pipe added to the support of the system..Also my system has no gaskets from headers to pipe. just tighten an tap with a light hammer an it will seal fine..not sure, but a mechanic friend told me to do that, an it worked fine.
     
    army grunt, Nov 13, 2015
    #5
  6. Nov 14, 2015
    oddfirejeeper

    oddfirejeeper Active Member

    Hamilton, MI
    Joined:
    May 5, 2004
    Messages:
    1,253
    wonder if anyone has done this system with the tank in the rear like a '71. because that is where the muffler goes in the older cj's. i would love to buy one of these systems but not sure if it will work. it states 66-71 but like i said the older cj's have the under seat tank
     
    oddfirejeeper, Nov 14, 2015
    #6
  7. Nov 14, 2015
    FinoCJ

    FinoCJ 1970 CJ5 Staff Member

    Bozeman, MT
    Joined:
    Jul 18, 2013
    Messages:
    5,625
    I called them and chatted about this exact issue over a year ago - they said they could work with that pretty easily. I think I even emailed them a photo of the FSM page that has the late 70 and 71 exhaust routing with rear tank. I am pretty sure they quoted me the exact same price as for a standard 66-early 70 exhaust. In the end, I ended up going with a local shop for a bit cheaper....but all my dealings with them were very encouraging and helpful, and certainly would recommend at least chatting with them.
     
    FinoCJ, Nov 14, 2015
    #7
  8. Jan 4, 2016
    vnulk

    vnulk New Member

    Oracle, AZ
    Joined:
    Jul 4, 2015
    Messages:
    4
    I purchased a Waldron system for my '70 V6 - Y pipe and standard muffler. It came quickly and installed without any issues. Great product and I highly recommend them.
     
    vnulk, Jan 4, 2016
    #8
    CJ568 likes this.
  9. Jan 8, 2016
    sparky6280

    sparky6280 New Member

    Rochester, New York
    Joined:
    Nov 14, 2015
    Messages:
    7
    I have a 71 V6 all original with the tank in the rear and Jon was able to accomodate and make a system for it. I went for the SS option and love it.....great people to work with.
     
    sparky6280, Jan 8, 2016
    #9
  10. Jul 5, 2016
    throwback

    throwback Member

    Joined:
    Sep 9, 2015
    Messages:
    68
    Bumping this to see if anyone else has used Waldron.
     
    throwback, Jul 5, 2016
    #10
  11. Jul 5, 2016
    CJ568

    CJ568 New Member

    Kilgore, TX
    Joined:
    Feb 16, 2016
    Messages:
    6
    I bought from them and it fit like a glove!
     
    CJ568, Jul 5, 2016
    #11
  12. Jul 5, 2016
    termin8ed

    termin8ed I didn't do it Staff Member

    Mason, MI
    Joined:
    Dec 22, 2002
    Messages:
    4,422
    I wanted to but the stock ypipe i had wouldnt work after i put a lift on. The driveshaft hit it. Anyone have them work around that or having both manifolds dump to the back? --ps added...
     
    termin8ed, Jul 5, 2016
    #12
New Posts