1. Registration trouble? Please use the "Contact Us" link at the bottom right corner of the page and your issue will be resolved.
    Dismiss Notice

Hand throttle to Carter YF

Discussion in 'Early CJ5 and CJ6 Tech' started by Howard Eisenhauer, Mar 30, 2014.

  1. Mar 30, 2014
    Howard Eisenhauer

    Howard Eisenhauer Administrator Staff Member

    Tantallon, Nova...
    Joined:
    Nov 22, 2003
    Messages:
    8,102
    Anyone got a clear pic of where/how the hand throttle cable connects to the carb?

    Thanks,

    H.
     
  2. Mar 30, 2014
    jasonjp62

    jasonjp62 Member

    Pennsboro WV.
    Joined:
    Aug 15, 2009
    Messages:
    799
  3. Mar 30, 2014
    Howard Eisenhauer

    Howard Eisenhauer Administrator Staff Member

    Tantallon, Nova...
    Joined:
    Nov 22, 2003
    Messages:
    8,102
  4. Mar 30, 2014
    jasonjp62

    jasonjp62 Member

    Pennsboro WV.
    Joined:
    Aug 15, 2009
    Messages:
    799
  5. Mar 30, 2014
    jasonjp62

    jasonjp62 Member

    Pennsboro WV.
    Joined:
    Aug 15, 2009
    Messages:
    799
  6. Mar 30, 2014
    jasonjp62

    jasonjp62 Member

    Pennsboro WV.
    Joined:
    Aug 15, 2009
    Messages:
    799
  7. Mar 30, 2014
    noahlon

    noahlon Old Fart

    Pine Ridge, AR
    Joined:
    Dec 22, 2010
    Messages:
    206
    need a bracket like that for my 2 bbl on my 225 V6 choke
     
  8. Mar 30, 2014
    Howard Eisenhauer

    Howard Eisenhauer Administrator Staff Member

    Tantallon, Nova...
    Joined:
    Nov 22, 2003
    Messages:
    8,102
    Jason, again thanks, but do you have a pic of the cable connected to the throttle linkage?

    H.
     
  9. Mar 31, 2014
    PeteL

    PeteL If it wasn't for physics, and law enforcement... 2024 Sponsor 2023 Sponsor 2022 Sponsor

    Hills of NH
    Joined:
    Aug 3, 2003
    Messages:
    9,754
    Howard,

    In this pic, at the lower right, there is a plate attached to the throttle arm, with a 1/4" hole very visible, and it has a 45ยบ upward bend exactly at the hole. That is correct OEM.

    http://i816.photobucket.com/albums/zz81/jasonjp62/20140330_182013_zpsxshwpzob.jpg

    The inner wire end of the throttle cable goes through that hole, then there is a ferrule-type screw stop clamped on the wire beyond/below the hole, adjusted to give just a little freeplay when 'shut'. Thus the throttle arm can operate independently without interference from the cable, freely slipping over the wire unless the hand throttle is pulled.
     
    Last edited: Mar 31, 2014
  10. Mar 31, 2014
    Howard Eisenhauer

    Howard Eisenhauer Administrator Staff Member

    Tantallon, Nova...
    Joined:
    Nov 22, 2003
    Messages:
    8,102
    Thanks Pete :)

    H.
     
  11. Mar 31, 2014
    jasonjp62

    jasonjp62 Member

    Pennsboro WV.
    Joined:
    Aug 15, 2009
    Messages:
    799
    [​IMG]



    This is on a solex, but its the same principle. like Pete described. I am missing the stop on the end of the cable.
     
    Last edited: Mar 31, 2014
  12. Mar 31, 2014
    Howard Eisenhauer

    Howard Eisenhauer Administrator Staff Member

    Tantallon, Nova...
    Joined:
    Nov 22, 2003
    Messages:
    8,102
    Thanks Jason, I'll probably end up fabbing a barrel stop.

    H.
     
  13. Mar 31, 2014
    PeteL

    PeteL If it wasn't for physics, and law enforcement... 2024 Sponsor 2023 Sponsor 2022 Sponsor

    Hills of NH
    Joined:
    Aug 3, 2003
    Messages:
    9,754
    Barrel stop! That's the word I was trying to come up with. You can buy blister-packs of them in assorted sizes at my FLAPS.
     
  14. Apr 1, 2014
    Howard Eisenhauer

    Howard Eisenhauer Administrator Staff Member

    Tantallon, Nova...
    Joined:
    Nov 22, 2003
    Messages:
    8,102
    Yup that's where I found them- at the fourth place I went to :rofl:

    First two they didn't have a clue what I was talking about, next one the guy knew what they are but didn't have any, fourth place I went to not expecting to find them there (auto parts/garden stuff/kitchen widjits place- I had time to kill & it was on the way) I was cruising the self-help displays & ready to give up when the counter guy asked what I was looking for- he knew exactly what they were & exactly where to find them (fortunately he's needed them in the past for his Vespa :D).

    For those of you in future centuries mind linking to these posts because your Way-Back Machine search brought them up you want a Dorman "Help" pack p/n 03336. :)

    H.
     
  15. Dec 6, 2015
    mickeykelley

    mickeykelley Well-Known Member

    Republic of Texas
    Joined:
    Oct 10, 2015
    Messages:
    1,900
    I'm missing the extra plate which is screwed onto the throttle for the cable to go thru. Where do I find that extra plate? I know I could try to fab something, but wanting to find real one. Here is mine right now.

    image.jpg
     
  16. Dec 7, 2015
    PeteL

    PeteL If it wasn't for physics, and law enforcement... 2024 Sponsor 2023 Sponsor 2022 Sponsor

    Hills of NH
    Joined:
    Aug 3, 2003
    Messages:
    9,754
New Posts