1. Registration trouble? Please use the "Contact Us" link at the bottom right corner of the page and your issue will be resolved.
    Dismiss Notice

Recent Content by Streeetch

  1. Streeetch
    Post

    My CJ2A/3A/M38 +12"

    yeah I've been looking for one... unfortunately the jeep that I got my rear axle from was robbed of it's flywheel and bellhousing... dude said I...
    Post by: Streeetch, Dec 3, 2015 in forum: Builds and Fabricators Forum
  2. Streeetch
    Post

    My CJ2A/3A/M38 +12"

    little update... haven't found the time to upload all my photos until now... I had quite the productive long change this week. after I got the...
    Post by: Streeetch, Dec 3, 2015 in forum: Builds and Fabricators Forum
  3. Streeetch
    Post

    My CJ2A/3A/M38 +12"

    Problem is, I don't have a stock flywheel. The motor I'm using is from a car with an auto. Thanks for your input, I was reading the tech vault...
    Post by: Streeetch, Dec 3, 2015 in forum: Builds and Fabricators Forum
  4. Streeetch
    Post

    My CJ2A/3A/M38 +12"

    Made some progress... I got the bed back in place, along with my riser panel. [IMG] I think tomorrow I'm going to drag the M38 in and start...
    Post by: Streeetch, Nov 30, 2015 in forum: Builds and Fabricators Forum
  5. Streeetch
    Post

    New Jeep! My 48 CJ2A

    I really like your axle holding fixture for the engine stand... any details on it?
    Post by: Streeetch, Nov 29, 2015 in forum: Builds and Fabricators Forum
  6. Streeetch
    Post

    Varg In Jeep's Clothing

    :cool::cool::cool: Kudos to you! Interesting to see the level of craftsmanship that can be achieved with some knowledge and patience.
    Post by: Streeetch, Nov 22, 2015 in forum: Builds and Fabricators Forum
  7. Streeetch
    Post

    My CJ2A/3A/M38 +12"

    Thought I'd post an update... I finally just bit the bullet and ordered up most of my metal from Classic Enterprises... floor panels, riser, hat...
    Post by: Streeetch, Nov 22, 2015 in forum: Builds and Fabricators Forum
  8. Streeetch
    Post

    Swinging pedals

    Great info... one of the tubs I have was already converted to swinging pedals. Hopefully I'll be in for an easy swap, once I get there. There's...
    Post by: Streeetch, Nov 17, 2015 in forum: Builds and Fabricators Forum
  9. Streeetch
    Post

    Todays $25 Center Console

    Nice! I bought a 50 mm can for the back of my truck... perfect size for holding a tow strap, jumper cables, gloves, etc. I've always thought...
    Post by: Streeetch, Nov 17, 2015 in forum: Builds and Fabricators Forum
  10. Streeetch
    Post

    My CJ2A/3A/M38 +12"

    Thanks, guys... I'm torn about what to do, I spent probably three hours separating sheetmetal on the floor riser, and the metal is very heavily...
    Post by: Streeetch, Nov 17, 2015 in forum: Builds and Fabricators Forum
  11. Streeetch
    Post

    My CJ2A/3A/M38 +12"

    Yeah I've pretty much worn out my KW catalog thumbing through it! Anybody have some ideas on what to treat metal with that is really rusty, yet...
    Post by: Streeetch, Nov 16, 2015 in forum: Builds and Fabricators Forum
  12. Streeetch
    Post

    My CJ2A/3A/M38 +12"

    Today's update: I felt like cutting some sheetmetal today... [IMG] Keep in mind the doors will only be stretched 6" instead of the full 12" shown...
    Post by: Streeetch, Nov 16, 2015 in forum: Builds and Fabricators Forum
  13. Streeetch
    Post

    My CJ2A/3A/M38 +12"

    Yeah novak seems like a good place, and they're somewhat local to me. The reasoning behind lengthening hood is not necessarily for room, but...
    Post by: Streeetch, Nov 16, 2015 in forum: Builds and Fabricators Forum
  14. Streeetch
    Post

    My CJ2A/3A/M38 +12"

    Thank you, sir! Do you have any experience with the block hugger headers from novak? I was trying to figure out what all I'll need to get my...
    Post by: Streeetch, Nov 14, 2015 in forum: Builds and Fabricators Forum
  15. Streeetch
    Post

    My CJ2A/3A/M38 +12"

    I took your guys' advice and started on the body. There's still a bunch of rust, especially around the toolbox area! I cut it out after I...
    Post by: Streeetch, Nov 13, 2015 in forum: Builds and Fabricators Forum
New Posts