1. Registration trouble? Please use the "Contact Us" link at the bottom right corner of the page and your issue will be resolved.
    Dismiss Notice

Lockman's Recent Activity

  1. Lockman liked Cap-n-Cray's post in the thread Interesting Air Compressor.

    This is the Jun-Air I have... [IMG] [IMG] All I know is it is very quiet... One of my job site compressors... [IMG] It is...

    Dec 12, 2019 at 6:35 AM
  2. Lockman attached a file to the thread Interesting Air Compressor.

    I have used the same Thomas Air-Pac for over 30 years . Very Cool. Oil less , Teflon, quiet & light weight. Used it inside homes for...

    Thomas AirPac.jpg Dec 11, 2019 at 8:07 PM
  3. Lockman attached a file to the thread WTB 11" Drum Brake Backing Plate.

    Hi Ken , I have a set , but there off my CJ5 , with a Dana 30 Axel ? Some one else will most likely have more knowledge of possible...

    Bendix.JPG Dec 11, 2019 at 7:33 PM
  4. Lockman liked kenb's post in the thread WTB 11" Drum Brake Backing Plate.

    Hello, I'm looking for some 11" drum brake backing plates to work with my M38A1. Just looking for fronts at this time. If anyone has...

    Dec 11, 2019 at 7:01 PM
  5. Lockman replied to the thread Factory Engine Bay Photos?.

    Maury...... You Sir , have Found one beautiful CJ5 there. :drool;

    Dec 10, 2019 at 5:49 PM
  6. Lockman liked maurywhurt's post in the thread Factory Engine Bay Photos?.

    Here's another shot of a 1965 Tux F134 engine compartment. This Jeep is reportedly a one-owner vehicle with 14,000 original miles: [IMG]

    Dec 10, 2019 at 5:46 PM
  7. Lockman liked ITLKSEZ's post in the thread The Official "What The Heck Is This?" Thread.

    The male is 1/8” NPT

    Dec 10, 2019 at 4:40 PM
  8. Lockman replied to the thread The Official "What The Heck Is This?" Thread.

    So...... it's called an Inverted Flare elbow. The male end is 1/8" NPT . The female inverted flare, comes in 3) sizes : 3/16" , 1/4 " ,...

    Dec 10, 2019 at 4:25 PM
  9. Lockman liked ITLKSEZ's post in the thread The Official "What The Heck Is This?" Thread.

    I just ran down and checked. On the back of the f- head, right? Mine is a 1/8” NPT to compression elbow. It would probably be easier to...

    Dec 9, 2019 at 6:38 PM
  10. Lockman replied to the thread The Official "What The Heck Is This?" Thread.

    X3 . The Independent Hardware that I work for has this, also . It's a brass , Flared 90 . I believe its 3/8" male to 1/2" female?...

    Dec 9, 2019 at 4:10 PM
  11. Lockman replied to the thread Show Us Your Jeep!.

    Thanks for posting the pic of your '74 , Tim. I just received a rim & side tire carrier, on a ' Pay It Forward' from my newest friend ,...

    Dec 9, 2019 at 4:01 PM
  12. Lockman liked shadetreetim's post in the thread Show Us Your Jeep!.

    Thanksgiving weekend was our much anticipated trip to Havasu Landing for their annual Poker Run across the desert. This being the CJ5's...

    Dec 9, 2019 at 3:47 PM
New Posts