1. Registration trouble? Please use the "Contact Us" link at the bottom right corner of the page and your issue will be resolved.
    Dismiss Notice

Recent Content by jeepfreak81

  1. jeepfreak81
    Post

    225 V6 ignition options and opinions

    I run Pertronix, I have really liked it. Runs smooth as an oddfire can.
    Post by: jeepfreak81, Apr 22, 2014 in forum: Early CJ5 and CJ6 Tech
  2. jeepfreak81
    Post

    My Flatty... From the start

    [IMG] [IMG] YouTube Still figuring out the 4 speed, gear selection is everything in the snow with skinny tires and 3.73 gears. Unfortunately my...
    Post by: jeepfreak81, Feb 5, 2014 in forum: Builds and Fabricators Forum
  3. jeepfreak81
    Post

    4th gear no engine power

    Honestly, I found the problem, I must have bumped the timing working on it. It was too advanced. I put the light on it and retarded it and that...
    Post by: jeepfreak81, Jan 24, 2014 in forum: Early CJ5 and CJ6 Tech
  4. jeepfreak81
    Post

    My Flatty... From the start

    [IMG] [IMG] [IMG] [IMG] Sent from my HTC6435LVW using Tapatalk
    Post by: jeepfreak81, Jan 23, 2014 in forum: Builds and Fabricators Forum
  5. jeepfreak81
    Post

    4th gear no engine power

    No points, I converted to the Pertronix, how do I check the vacuum advance?
    Post by: jeepfreak81, Jan 22, 2014 in forum: Early CJ5 and CJ6 Tech
  6. jeepfreak81
    Thread

    4th gear no engine power

    225 V6 and the Rochester 2G carb. I have power down low, and it seems to accelerate well and idle well. I was plowing snow fine. Once I reach...
    Thread by: jeepfreak81, Jan 22, 2014, 10 replies, in forum: Early CJ5 and CJ6 Tech
  7. jeepfreak81
    Post

    My Flatty... From the start

    Insulating the top a bit for the snow run this weekend. It's going to be a cold one. [IMG] [IMG] [IMG] [IMG]
    Post by: jeepfreak81, Jan 21, 2014 in forum: Builds and Fabricators Forum
  8. jeepfreak81
    Post

    My Flatty... From the start

    I forgot to leave the video in here.... Plowing with the flatfender Willys Jeep. - YouTube Windshield in [IMG] Doors on, and aligned [IMG]...
    Post by: jeepfreak81, Jan 21, 2014 in forum: Builds and Fabricators Forum
  9. jeepfreak81
    Post

    CJ6 with T98 Trans mount, where to buy mount?

    The mount listed above worked beautifully. We did my engine mounts to while I was at it Sent from my HTC6435LVW using Tapatalk
    Post by: jeepfreak81, Jan 21, 2014 in forum: Early CJ5 and CJ6 Tech
  10. jeepfreak81
    Post

    225 rich on pass side bank, lean on drivers side.

    Finally bought the above cap, going to try it, but it still has the points window like the one I have and looks the same upon initial inspection....
    Post by: jeepfreak81, Jan 16, 2014 in forum: Early CJ5 and CJ6 Tech
  11. jeepfreak81
    Post

    225 rich on pass side bank, lean on drivers side.

    I am having the same issue as the OP, and I am trying to determine if my distributor is the same as his before I just throw parts at it, I do not...
    Post by: jeepfreak81, Jan 11, 2014 in forum: Early CJ5 and CJ6 Tech
  12. jeepfreak81
    Post

    225 rich on pass side bank, lean on drivers side.

    Best I could do right now as I didn't have time to pull the dizzy and I have to drive it in the am to town. I couldn't see any markings. Can you...
    Post by: jeepfreak81, Jan 10, 2014 in forum: Early CJ5 and CJ6 Tech
  13. jeepfreak81
    Post

    225 rich on pass side bank, lean on drivers side.

    Ok now how do I figure it out, I have the RR 184 on my jeep, right bank running rich, same as you had. But I do not know if it's a Delco...
    Post by: jeepfreak81, Jan 9, 2014 in forum: Early CJ5 and CJ6 Tech
  14. jeepfreak81
    Post

    225 rich on pass side bank, lean on drivers side.

    Thanks, I still have the box for mine I think, I will look when I get home. I need to make a trip to Napa anyway .
    Post by: jeepfreak81, Jan 9, 2014 in forum: Early CJ5 and CJ6 Tech
New Posts