1. Registration trouble? Please use the "Contact Us" link at the bottom right corner of the page and your issue will be resolved.
    Dismiss Notice

Recent Content by DKillam

  1. DKillam
    Post

    F-134 oil prime?

    I read the thread yesterday and from what I could tell the seal I took out looks like the seal that failed on Howards rebuild. The new seal I...
    Post by: DKillam, Jan 28, 2009 in forum: Early CJ5 and CJ6 Tech
  2. DKillam
    Thread

    Driveshaft woes

    I'm knee-deep into replacing seals and gaskets that don't require removal of transmission or transfer case - so far, so good! I've pulled both...
    Thread by: DKillam, Jan 25, 2009, 2 replies, in forum: Early CJ5 and CJ6 Tech
  3. DKillam
    Post

    Well,Heres Mine!

    Welcome from San Angelo, Texas. Nice looking Jeep. Good to have another '62 on board! :)
    Post by: DKillam, Jan 21, 2009 in forum: Builds and Fabricators Forum
  4. DKillam
    Post

    Oil Filter Cannister...

    If you don't have any luck finding an o-ring or gasket, how about cleaning the area where the gasket goes and lay in a bead of silicon gasket...
    Post by: DKillam, Jan 17, 2009 in forum: Early CJ5 and CJ6 Tech
  5. DKillam
    Post

    1964 CJ5 - Chevy motor swap?

    R) Then you would want more HP/torque :v6: then SBC :twisted:
    Post by: DKillam, Jan 16, 2009 in forum: Early CJ5 and CJ6 Tech
  6. DKillam
    Post

    Welding Helmet

    Miller Elite is my favorite! Large window, easily adjustable & comfortable headband, grind mode, adjustable shade... :) Of course I used a...
    Post by: DKillam, Jan 14, 2009 in forum: Shop Safety
  7. DKillam
    Post

    F-134 oil prime?

    Thanks for the support! After replacing the side and top valve cover gaskets this morning, I filled the crankcase with oil, cranked on the engine...
    Post by: DKillam, Jan 9, 2009 in forum: Early CJ5 and CJ6 Tech
  8. DKillam
    Post

    F-134 oil prime?

    What I thought - oh well :roll: Considered using assembly lube but Fel-pro instructions recommended only oil. Thanks Billy.
    Post by: DKillam, Jan 9, 2009 in forum: Early CJ5 and CJ6 Tech
  9. DKillam
    Thread

    F-134 oil prime?

    Just finished replacing rear main seal (engine in jeep) and was able to change upper seal without loosening other main caps or turning the crank....
    Thread by: DKillam, Jan 9, 2009, 11 replies, in forum: Early CJ5 and CJ6 Tech
  10. DKillam
    Post

    wiring harness

    I used an EZ 21 circuit along with www.madelectrical.com accessories - Start-em up kit, alternator kit, junction blocks and relay kits - best on...
    Post by: DKillam, Dec 19, 2008 in forum: Early CJ5 and CJ6 Tech
  11. DKillam
    Post

    64 CJ5 front seats

    Carburetor kit source: http://www.earlycj5.com/forums/showthread.php?p=670743#post670743
    Post by: DKillam, Dec 16, 2008 in forum: Early Jeep Restoration and Research
  12. DKillam
    Post

    Just wanting to say thanks from a new guy

    Welcome from San Angelo, Texas! I'd say run the tires you have if they're in decent shape (but I'm cheap :roll:). The oil pressure sounds about...
    Post by: DKillam, Dec 9, 2008 in forum: Early CJ5 and CJ6 Tech
  13. DKillam
    Post

    Information needed, F Head

    I ordered a kit from The Carburetor Shop, LLC (www.thecarburetorshop.com) on Sparky's recommendation. It's a CS-1822 for a Carter YF - $65.00 +...
    Post by: DKillam, Dec 3, 2008 in forum: Early CJ5 and CJ6 Tech
New Posts