1. Registration trouble? Please use the "Contact Us" link at the bottom right corner of the page and your issue will be resolved.
    Dismiss Notice

Recent Content by BrenGun

  1. BrenGun
    Post

    The beginning of my '53 CJ3B build/resto

    R)
    Post by: BrenGun, Aug 4, 2013 in forum: Builds and Fabricators Forum
  2. BrenGun
    Post

    The beginning of my '53 CJ3B build/resto

    Well, I've been playing around with first dry and then greased up needle bearings and going back and forth between dropping them and not being...
    Post by: BrenGun, Aug 4, 2013 in forum: Builds and Fabricators Forum
  3. BrenGun
    Post

    The beginning of my '53 CJ3B build/resto

    Makes sense... I've since found this out in a manual. I had thought that the tab had something to do with the locking mechanism and based on the...
    Post by: BrenGun, Aug 1, 2013 in forum: Builds and Fabricators Forum
  4. BrenGun
    Post

    The beginning of my '53 CJ3B build/resto

    RockRunner85, thanks, good advice that. Now for a combo update... And there was another weekend. I needed to get into the barn yesterday and...
    Post by: BrenGun, Jul 31, 2013 in forum: Builds and Fabricators Forum
  5. BrenGun
    Post

    The beginning of my '53 CJ3B build/resto

    PS. the rear pinion isn't leaking. I was a bit shortsighted and realized that it would stop leaking when I torqued down the yoke! Just glad that...
    Post by: BrenGun, May 21, 2013 in forum: Builds and Fabricators Forum
  6. BrenGun
    Post

    The beginning of my '53 CJ3B build/resto

    Good news and bad. Took the old clutch throwout bearing off and easily installed the new in the vise and then realized that the rear pinion seal...
    Post by: BrenGun, Apr 21, 2013 in forum: Builds and Fabricators Forum
  7. BrenGun
    Post

    The beginning of my '53 CJ3B build/resto

    One of the first nice days of the year so the boys and I got outside to play and work on the Mistress. A few little things done. I installed the...
    Post by: BrenGun, Apr 15, 2013 in forum: Builds and Fabricators Forum
  8. BrenGun
    Post

    The beginning of my '53 CJ3B build/resto

    Sitting around the house on yet another below 40 degree early spring day and feeling anxious and I realized what was up... I needed to get my...
    Post by: BrenGun, Mar 23, 2013 in forum: Builds and Fabricators Forum
  9. BrenGun
    Post

    my 1946 CJ2A build thread

    Hey, mine looked much worse than that four or five years ago when I first got her. Now she still is incomplete and not even running yet, but its a...
    Post by: BrenGun, Sep 25, 2012 in forum: Builds and Fabricators Forum
  10. BrenGun
    Post

    The beginning of my '53 CJ3B build/resto

    Yay, small steps! I finally got around to ordering the replacement pressure plate bolts from Walck's a couple of weeks ago. Got a UPS tracking...
    Post by: BrenGun, Sep 24, 2012 in forum: Builds and Fabricators Forum
  11. BrenGun
    Post

    The beginning of my '53 CJ3B build/resto

    Slow progress/ no progress... Forgot to post that last week I did get that broken bolt out. I bought an easy out set that seemed to have alot of...
    Post by: BrenGun, Sep 8, 2012 in forum: Builds and Fabricators Forum
  12. BrenGun
    Post

    The beginning of my '53 CJ3B build/resto

    So I also need to invest in something better than my little old tap and die set. Anyone have a recommendation for a good quality, preferably...
    Post by: BrenGun, Aug 18, 2012 in forum: Builds and Fabricators Forum
  13. BrenGun
    Post

    The beginning of my '53 CJ3B build/resto

    One step forward and two back today, man am I bummed... :( But first the good news- I spun the pilot bushing on the end of a taped up bit on my...
    Post by: BrenGun, Aug 18, 2012 in forum: Builds and Fabricators Forum
  14. BrenGun
    Post

    The beginning of my '53 CJ3B build/resto

    Didn't get much done today, still too damned humid to feel like moving. Tried tapping in the pilot bushing after taking it from the freezer......
    Post by: BrenGun, Aug 12, 2012 in forum: Builds and Fabricators Forum
  15. BrenGun
    Post

    The beginning of my '53 CJ3B build/resto

    Another scorcher today that really sapped my drive. Got a bit done though... Cleaned up the flywheel to look nice and purty with a bit more...
    Post by: BrenGun, Aug 6, 2012 in forum: Builds and Fabricators Forum
New Posts