1. Registration trouble? Please use the "Contact Us" link at the bottom right corner of the page and your issue will be resolved.
    Dismiss Notice

Recent Content by 73CJ89XJ

  1. 73CJ89XJ
    Post

    CJ T-18 won't bolt flush to my engine

    Using a mirror I was able to see that the splines had engaged and the shaft slid at least in to the disc.
    Post by: 73CJ89XJ, Apr 4, 2006 in forum: Intermediate CJ-5/6/7/8
  2. 73CJ89XJ
    Post

    CJ T-18 won't bolt flush to my engine

    It is a 6:1 CJ T-18A that is replacing a T-14. I used a pilot bushing out of the clutch kit that I bought. It had 3 and I could have sworn it was...
    Post by: 73CJ89XJ, Apr 4, 2006 in forum: Intermediate CJ-5/6/7/8
  3. 73CJ89XJ
    Post

    CJ T-18 won't bolt flush to my engine

    Whoops I just noticed I didn't put this in the intermediate forum. Sorry guys
    Post by: 73CJ89XJ, Apr 4, 2006 in forum: Intermediate CJ-5/6/7/8
  4. 73CJ89XJ
    Thread

    CJ T-18 won't bolt flush to my engine

    For some reason the CJ T18 I am trying to swap into my 73 CJ5 with a 258 is not fully sliding in. It seems to be stuck about 1/4 of an inch away...
    Thread by: 73CJ89XJ, Apr 4, 2006, 8 replies, in forum: Intermediate CJ-5/6/7/8
  5. 73CJ89XJ
    Post

    T18 swap

    What throwout bearing is everyone using? The T18 shaft is larger than my current T14. I have a jeep bellhousing and jeep T18a.
    Post by: 73CJ89XJ, Mar 2, 2006 in forum: Intermediate CJ-5/6/7/8
  6. 73CJ89XJ
    Post

    DIY Bedliners...Who has any suggestions

    I did herculiner on my XJ and have no complaints
    Post by: 73CJ89XJ, May 7, 2005 in forum: Intermediate CJ-5/6/7/8
  7. 73CJ89XJ
    Post

    Body Mount Locations??

    I think there was 13 mounts on my 73. The radiator 2 where the fenders meet the tub 4 in the front passenger area 2 above the rear tires 4...
    Post by: 73CJ89XJ, May 6, 2005 in forum: Intermediate CJ-5/6/7/8
  8. 73CJ89XJ
    Post

    Windshield seal

    I have an inermediate windshield and it fit perfectly. I think they just make them with a little extra length.
    Post by: 73CJ89XJ, May 5, 2005 in forum: Early Jeep Restoration and Research
  9. 73CJ89XJ
    Post

    I have a 73 wiring diagram in .dwg format

    Ok I added both the links to the first post
    Post by: 73CJ89XJ, May 2, 2005 in forum: Intermediate CJ-5/6/7/8
  10. 73CJ89XJ
    Post

    I have a 73 wiring diagram in .dwg format

    I tried to convert it to a png but it froze my AWFUL work computer :mad: It's a jpeg and it's readable now. I just need to find a free ftp program...
    Post by: 73CJ89XJ, May 2, 2005 in forum: Intermediate CJ-5/6/7/8
  11. 73CJ89XJ
    Post

    I have a 73 wiring diagram in .dwg format

    On monday I'll convert it to a big ole jpg and rehost it
    Post by: 73CJ89XJ, May 1, 2005 in forum: Intermediate CJ-5/6/7/8
  12. 73CJ89XJ
    Post

    I have a 73 wiring diagram in .dwg format

    I just decided to host it on my website now that I got it off my work computer. Here's a link: http://www.73cj89xj.com/CJ/CJHarness.DWG And...
    Post by: 73CJ89XJ, Apr 30, 2005 in forum: Intermediate CJ-5/6/7/8
  13. 73CJ89XJ
    Post

    I have a 73 wiring diagram in .dwg format

    Kinkos? Office Max?
    Post by: 73CJ89XJ, Apr 29, 2005 in forum: Intermediate CJ-5/6/7/8
  14. 73CJ89XJ
    Post

    Anyone near their lowbacks with a tape measure

    Mainly just trying to figure out what width seat I can stuff in there. In my infinite wisdom I bought a wide tuffy box before I knew that I should...
    Post by: 73CJ89XJ, Apr 29, 2005 in forum: Intermediate CJ-5/6/7/8
New Posts