1. Registration trouble? Please use the "Contact Us" link at the bottom right corner of the page and your issue will be resolved.
    Dismiss Notice

Varg In Jeep's Clothing

Discussion in 'Builds and Fabricators Forum' started by ITLKSEZ, Aug 20, 2015.

  1. Jul 29, 2020
    Admiral Cray

    Admiral Cray I want to do this again.. Staff Member

    Bainbridge...
    Joined:
    Sep 21, 2009
    Messages:
    204,347
    Maybe that's the Focker gun...
     
    Twin2, bigbendhiker and ITLKSEZ like this.
  2. Jul 29, 2020
    ITLKSEZ

    ITLKSEZ Hope for the best, prepare for the worst

    Liberty Lake, WA
    Joined:
    Aug 13, 2015
    Messages:
    6,656
    I spent about 3 hours today with a torch to the frame horns. All the welding I did around them had left them less than straight. I knew this would need to be addressed eventually, but with nothing but a bumper and winch in that real estate, it wasn't critical for operation until now.

    When I started, using the grill as a guide, the PS frame rail hooked hard to the right 3/8” and up 1/4”, and the DS rail hooked right 1/4” but was flat. (I had the clamp holding the rails parallel for reference and for expansion resistance.)

    [​IMG]

    Torchy torchy...

    [​IMG]

    I also roughed out the parts for the winch plate/front crossmember. More on this tomorrow.

    [​IMG]

    Also, the insulation, application roller, and 3-pin headlight sockets I ordered yesterday already arrived today. o_O
     
    tymbom, Rich M., Fireball and 3 others like this.
  3. Jul 29, 2020
    Focker

    Focker That's a terrible idea...What time? Staff Member

    WA
    Joined:
    Aug 18, 2014
    Messages:
    7,540
    That's what I almost posted... I thought I saw my name for a split second. :whistle:
     
  4. Jul 30, 2020
    45es

    45es Active Member 2024 Sponsor 2023 Sponsor 2022 Sponsor

    Naches, WA
    Joined:
    Mar 31, 2007
    Messages:
    1,103
    You know it will bug you ever day if you don't fix it now. It will be the only thing you see when walking near the jeep. Easy fix now. Do it.
     
  5. Jul 30, 2020
    ITLKSEZ

    ITLKSEZ Hope for the best, prepare for the worst

    Liberty Lake, WA
    Joined:
    Aug 13, 2015
    Messages:
    6,656
    I’m gonna have a whole lot more to fix by the time I’m done. If I fix every mistake as it happens, I’ll just be chasing my tail. Getting the cage in is going to require extensive paint fixes. :oops:
     
  6. Jul 30, 2020
    Boyink

    Boyink Super Moderator Staff Member

    Tulsa, OK
    Joined:
    Sep 20, 2002
    Messages:
    6,193
    Eh - about the 4th trip offroad something will happen to the paint where that run wont be such a huge issue anymore...;)
     
    ITLKSEZ likes this.
  7. Jul 30, 2020
    Admiral Cray

    Admiral Cray I want to do this again.. Staff Member

    Bainbridge...
    Joined:
    Sep 21, 2009
    Messages:
    204,347
    This prototype is going off road?... :confused:
     
  8. Jul 30, 2020
    sterlclan

    sterlclan Member 2022 Sponsor

    exploring the...
    Joined:
    Feb 21, 2009
    Messages:
    3,869
    That’s not a run it’s a sag sheesh wait till it’s cured and plane the high spots off with a razor blade at a 90to the paint and buff it out.
     
    ojgrsoi and ITLKSEZ like this.
  9. Jul 30, 2020
    ITLKSEZ

    ITLKSEZ Hope for the best, prepare for the worst

    Liberty Lake, WA
    Joined:
    Aug 13, 2015
    Messages:
    6,656
    :twist:
     
  10. Jul 30, 2020
    whatroad

    whatroad New Member

    Joined:
    Jul 3, 2009
    Messages:
    1

    Hey Rookie,.... that’s not a run. It’s called a flow check.
     
    ITLKSEZ likes this.
  11. Jul 30, 2020
    ITLKSEZ

    ITLKSEZ Hope for the best, prepare for the worst

    Liberty Lake, WA
    Joined:
    Aug 13, 2015
    Messages:
    6,656
    Winch mount/crossmember is 90% done. It still needs drain and mount holes.

    [​IMG]

    The section on the right is capped off and will get another section of 2 x 4 x 1/8” tubing welded under it. They will be connected internally, and it will act as the vacuum reservoir. I offset the winch for this purpose, and also, the bumper will be the air tank, and I allowed the area next to the winch for room for the air fitting, and hand space to operate it.

    [​IMG]

    The asymmetry is going to kill my wife. :rofl:
     
    blalp!, fhoehle, Twin2 and 8 others like this.
  12. Jul 30, 2020
    FinoCJ

    FinoCJ 1970 CJ5 Staff Member

    Bozeman, MT
    Joined:
    Jul 18, 2013
    Messages:
    5,593
    yea - that asymmetry is a bit unnerving - the REP 8000 I run is asymmetrical, so even with a centered winch plate and mount, its longer on the motor side than the clutch side by about 1.5 inches. Good thing is I can't see it when i am driving. Heck, even the asymmetrical nature of the radiator behind the grill in the wagon bothers me....as do the seats in an intermediate cj5....
     
    fhoehle and ITLKSEZ like this.
  13. Jul 30, 2020
    ITLKSEZ

    ITLKSEZ Hope for the best, prepare for the worst

    Liberty Lake, WA
    Joined:
    Aug 13, 2015
    Messages:
    6,656
    My entire drivetrain is offset pretty severely to the driver’s side to allow the exhaust to pass the clocked-flat T-case. Without a sway bar, this thing has some serious Jeep lean. Reason #3 for the offset.
     
  14. Jul 30, 2020
    FinoCJ

    FinoCJ 1970 CJ5 Staff Member

    Bozeman, MT
    Joined:
    Jul 18, 2013
    Messages:
    5,593
    I think it is/was OME that set-up their aftermarket lift, TJ coil springs a bit different on driver vs passenger side to compensate for some sort of lean. Don't remember the details, but it rode quite a bit higher on the driver side than the passenger (So we flipped the rear spring left to right to help balance it out - think it was a trick we found on the internet and its still running that way 10 years later with no issues). Anyway - I may have missed it 500 posts back - but do you have any designed differences in springs based on the drivetrain offset?
     
  15. Jul 30, 2020
    ITLKSEZ

    ITLKSEZ Hope for the best, prepare for the worst

    Liberty Lake, WA
    Joined:
    Aug 13, 2015
    Messages:
    6,656
    No, once everything is in this thing, it’s fairly level. But when the body and cage are out and the springs are still up in their “soft” range, it’s definitely noticeable. It doesn’t take much effort to get the sway bar to line up when in final form.

    That being said, the front springs are squashing down pretty far, and the spring adjustments are maxed out. I was guessing when I built around these springs, and I guessed a little light. I might end up getting some heavier front springs. That would help the situation even more.

    I was hoping I’d have enough money left at the end for some airbag helpers in the back. I’d love if I could put a dirt bike carrier on the back, but it would be riding on the bump stops, and heavier rear springs aren’t an option. It would be great to just pump up the rear and go.
     
    FinoCJ likes this.
  16. Jul 30, 2020
    ITLKSEZ

    ITLKSEZ Hope for the best, prepare for the worst

    Liberty Lake, WA
    Joined:
    Aug 13, 2015
    Messages:
    6,656
    The lug nuts, CV rebuild kit, and the wiring harness arrived today. I officially have enough to keep me busy for months. :waiting:
     
    Rich M., tymbom and Fireball like this.
  17. Jul 30, 2020
    ITLKSEZ

    ITLKSEZ Hope for the best, prepare for the worst

    Liberty Lake, WA
    Joined:
    Aug 13, 2015
    Messages:
    6,656
    I don’t know if anyone is interested, but I shot a video of a weld today. It’s 1/4” thick material, fully beveled on the top side. It’s a single pass with .030” wire. It’s hard to see, but in order to not blow through, I had to spread the heat around with a weave that was about 1 1/4” long. The resulting weld made bottom of the seam convex; over 100% penetration. I’m not showing off, just showing how, for anyone interested in technique. The weave pattern is hard to see, but it basically looks like a sideways pointy teardrop, with the point reaching further into the bevel with each weave, then backing up into the puddle to backfill. So the point of the teardrop penetrates through the seam, but then it is backed off before it blows through.

     
    ojgrsoi, Twin2, Desert Runner and 5 others like this.
  18. Jul 31, 2020
    Admiral Cray

    Admiral Cray I want to do this again.. Staff Member

    Bainbridge...
    Joined:
    Sep 21, 2009
    Messages:
    204,347
    My eyes, my eyes...
     
    Muzikp and Twin2 like this.
  19. Jul 31, 2020
    47v6

    47v6 junk wrecker! 2023 Sponsor 2022 Sponsor

    USA
    Joined:
    Oct 25, 2006
    Messages:
    5,798
    Mine too! I am blinded!!
     
    Twin2 likes this.
  20. Jul 31, 2020
    ITLKSEZ

    ITLKSEZ Hope for the best, prepare for the worst

    Liberty Lake, WA
    Joined:
    Aug 13, 2015
    Messages:
    6,656
    Don’t encourage him. :crazy:

    :rofl:
     
    dozerjim, Twin2, Focker and 1 other person like this.
New Posts